oliver2-44 9,758 #26 Posted August 11, 2022 (edited) @Jiminoh While roll pins are very hard they can be drilled out with a carbide drill bit. I have a small set of Ryobi carbide bits from Home Depot that are labeled for tile or glass. I have drilled out steering wheel roll pins with them, They work very well. If that doesn’t work one of the Vendors that list in Red Square “Vendor Section”. A-Z Tractor Salvage might have one. Give him a call at 717-821-2542. He is located in Pa. You could also place an ad in the Classified section herein. PS We would love to see some pictures of your Restoration. Edited August 11, 2022 by oliver2-44 1 2 1 Share this post Link to post Share on other sites
wallfish 17,011 #27 Posted August 11, 2022 (edited) I just asked because it seemed like something else was going on with the part. Might have something for ya but I don't want to waste my time finding and pulling the part for no reason like it's not any good because the paint is scuffed or something. Something just seemed weird since Dave has been around here a long time and don't remember ever seeing any problems before. The roll pin needs to be removed to get this one too and just as you found, it's not always fun getting them out. Certainly not worth the $20 for my time to do it but if you can't find the thing I'd give it go to get you one. Wouldn't the roll pin need to be removed from your part anyway to install the new part? If AZ doesn't have what you need let me know Edited August 11, 2022 by wallfish 1 2 Share this post Link to post Share on other sites
WHX?? 48,828 #28 Posted August 11, 2022 I don't think you thought wrong. Lemme go look on my parts shed Jim @Jiminoh I may have one. I parted out two 1055s once and only used one on a resto..... If I can find it.... @Achto hasn't gotten around to clean out the parts shed yet.. 2 Share this post Link to post Share on other sites
Achto 27,597 #29 Posted August 11, 2022 12 minutes ago, WHX?? said: @Achto hasn't gotten around to clean out the parts shed yet I'm saving that for my retirement project. 2 Share this post Link to post Share on other sites
rjg854 11,378 #30 Posted August 11, 2022 By that time there will be more clay pots, fertilizer, and such in your way 4 Share this post Link to post Share on other sites
953 nut 55,290 #31 Posted August 11, 2022 Just for clarification please look at the attached drawing and think outside the box for a moment. If there is no way you can get the roll pin #47 out of arm #46 then you may want to consider buying the cross shaft #44 with arm #45 attached as well as arm #46. That way you can cut shaft #44, remove both halves and insert the replacement parts. Share this post Link to post Share on other sites
WHX?? 48,828 #32 Posted August 11, 2022 I'm goin in ...if I ain't out in an hour somebody notify my next of kin..... 1 1 6 Share this post Link to post Share on other sites
WHX?? 48,828 #33 Posted August 11, 2022 Ok made it out unscathed .... these have a PN of 4899 does that sound right? if so we hit the mother lode..... 1 2 Share this post Link to post Share on other sites
Snoopy11 5,714 #34 Posted August 11, 2022 On 8/9/2022 at 2:04 AM, Jiminoh said: I have a 855 that needs a new clutch pivot arm.its kind of holding up my restoration.any help locating one would be wonderful. There is one on Ebay that you could buy. https://www.ebay.com/itm/403691313742?chn=ps&norover=1&mkevt=1&mkrid=711-213727-13078-0&mkcid=2&itemid=403691313742&targetid=4580496732614417&device=c&mktype=&googleloc=&poi=&campaignid=418233788&mkgroupid=1230353745471221&rlsatarget=pla-4580496732614417&abcId=9300542&merchantid=51291&msclkid=5b6027d5f0ac1677dabe4520a8a16f03 Don Share this post Link to post Share on other sites
WHX?? 48,828 #35 Posted August 11, 2022 6 hours ago, 953 nut said: cut shaft #44, Wack away I got the whole nine yards.... 3 2 Share this post Link to post Share on other sites
Snoopy11 5,714 #36 Posted August 11, 2022 1 minute ago, WHX?? said: Wack away I got the whole nine yards.... Sorry Jim, I posted my "ebay" idea before I flipped to the next page and saw that you were risking your life and limb... Don Share this post Link to post Share on other sites
WHX?? 48,828 #37 Posted August 11, 2022 (edited) I PMed you Jim. I'll send the arm, shaft, pulley everything. Your choice of color.... patinaed or patinaed.... Be advised tho I may have to hold it ransome for of your project. We do like our 855s here. Picked this one up from @cschannuth last year. All original unmolested and runs like the day it was new. Then again what vintage model do we not like around here.... 1045 helping roast some corn. 🌽. Edited August 11, 2022 by WHX?? 3 3 Share this post Link to post Share on other sites
wallfish 17,011 #38 Posted August 11, 2022 Glad to see Jim @WHX?? saved me from the potential of any roll pin removal. That old frame it's on has been sitting out there for while! 1 1 1 Share this post Link to post Share on other sites
WHX?? 48,828 #39 Posted August 11, 2022 (edited) 15 hours ago, wallfish said: old frame it's on has been sitting out there for while I hear ya... another of 'Nut's rite of passage. Edited August 12, 2022 by WHX?? 1 Share this post Link to post Share on other sites
WHX?? 48,828 #40 Posted August 12, 2022 17 hours ago, Snoopy11 said: saw that you were risking your life and limb... Yep ....Kinda like walkin into Dan's garage..... 4 Share this post Link to post Share on other sites
WHX?? 48,828 #41 Posted August 12, 2022 In the mail Jimbo.... let's not forget about dem der ! 4 2 1 Share this post Link to post Share on other sites
Jiminoh 27 #42 Posted August 16, 2022 Im sorry,I forgot to Chuck back here. Thankyou Oliver i will Try that today and let you know how it went 4 Share this post Link to post Share on other sites
WHX?? 48,828 #43 Posted August 16, 2022 Looks good Mail man says your clutch parts should be there on Wednesday. 1 1 Share this post Link to post Share on other sites
squonk 41,145 #44 Posted August 16, 2022 (edited) On 8/11/2022 at 10:10 AM, WHX?? said: I'm goin in ...if I ain't out in an hour somebody notify my next of kin..... That ain't even half cluttered ya Sally! Yer goin on KP! Make use of this garbage can! Edited August 16, 2022 by squonk 1 Share this post Link to post Share on other sites
Jiminoh 27 #45 Posted August 17, 2022 Boy I sure know those parets Share this post Link to post Share on other sites
squonk 41,145 #46 Posted August 17, 2022 Once this is cleaned out.................... You can put this up out front! 7 1 Share this post Link to post Share on other sites
WHX?? 48,828 #47 Posted August 17, 2022 (edited) 23 hours ago, squonk said: Yer goin on KP! Make use of this garbage can! Now if I round filed all those parts I wouldn't had Jim's clutch would I?!?! Just guessing those 10mm did not cone from @Pullstart s shop? Edited August 17, 2022 by WHX?? 2 Share this post Link to post Share on other sites
squonk 41,145 #48 Posted August 17, 2022 Just now, WHX?? said: Now if I round filed all those parts I wouldn't had Jim's clutch would I?!?! Keep the parts. Ditch everything else. You can give those snow shovels to Kevin so he can keep his shop clean! Share this post Link to post Share on other sites
WHX?? 48,828 #49 Posted August 17, 2022 Guessing The Hosen would need more than a shovel ... 'sides I can't get rid of those... my main snow removal implements.... 2 Share this post Link to post Share on other sites
Jiminoh 27 #50 Posted September 1, 2022 I have some more pics of my 855 restoration 2 5 Share this post Link to post Share on other sites
