Blade

[WheelHorseEnjoyer 25]

How universal is the push blade? There is an auction coming up in my area and it has a wheel horse push blade on it. I dont know if it would fit my B100. I was hoping you you kind people on here could tell me about how universal the wheel horse blades are and about how high I should bid it up to. Thank you.

[gwest_ca-(File Mod) 11,046]

Very little difference in these models

Dozer DNA of long tractor frame dozer blades

1968 model 6-4111 - First to fit LONG & SHORT frame tractors and first to mount under the rear axle - replaced by

1969 model [6-4112 + 6-9621]

1970-73 model [6-4113 + 6-9622]

1973-74 model [6-4113 + 6-9623]

1974 model [6-4114 + 6-9624]

1974 model 6-2131

1975 model 6-2132

1976 model 6-2133

1976 model 66-42BC01

1977 model 76-42BC01

1978 model 86-42BC01

1979 model 96-42BC01

1980 model 06-42BC01

1981-1984 model 06-42BC02 (Up to here they are 42" wide)

 

1984-1989 model 06-48BC01 (They are now 48" wide)

1990 model 06-48BC02 (Last blade to have 3 angle positions)

1991-1993 model 06-48BC03 (First blade to have 5 angle positions)

1993-2001 model 79350 - (105-1502 kit adapts 2001 and older GT Classic-Series blades to fit 2002 and later tractors

2002 2004-2009 2012 model 79364 - (105-1501 kit adapts 79364 blade to fit 2001 and older GT Classic-Series)

[ri702bill 8,327]

Be sure the auction has ALL the pieces - you will need the clamp-on axle mount if you do not already have one. The wear edge  on the later polws is reversable - best scenario is it has a new edge - worst is both are worn down and needs to be replaced. Be sure all the mechanism to angle the plow is there - perhaps download the manual if you know the model number and familiarize yourself with all the pieces. I bought a used in very good condition 79350 48" complete setup about 5 years ago for $200 - wear edge had one good more year left in it...

Bill

Edited June 27, 2022 by ri702bill

[Ed Kennell 38,209]

 to the 

 

There are two different length plow frames.        The blades themselves are the same.        The plow frame attaches to the rear axle and requires the rear axle bracket.

 

I believe the B-100 is a short frame tractor and would require a short plow frame.       Plow frames with blade sell for around $150 in my area.    The axle bracket sells for $40.

[SylvanLakeWH 25,598]

 

And 

 

In Michigan the frame and blade go for about $125-150…

 

If linkages (cable release and adjustment rod) aren’t all there then I’d go a bit less as you would need to fabricate/ add those.

 

 

 

[roadapples 6,983]

[cafoose 3,355]

If it's a V frame like this it's too short.

 

Frame like this should work.

 

 

Make sure it's similar to this one and not for a vertical engine tractor:

 

 

Edited June 27, 2022 by cafoose

[WheelHorseEnjoyer 25]

@cafoose   Thank you that helped me figure out what it was.

[WheelHorseEnjoyer 25]

@cafoose   @roadapples @SylvanLakeWH @gwest_ca  @ri702bill @Ed Kennell Thank you to all that responded to my original decision! This blade was at the auction yesterday and here is what I came home with. I did come home with the blade but when I was looking at it it was missing the piece that went onto the tractor to make it go up and down. So I figured I would have to fabricate one. But then there was also a C-120 there which I said ah what the heck one more couldn't hurt and so I bought that for $90. (I got the blade for $40)  When I got it all unloaded and started to work on the C-120 I crawled under it and there the lift deal that went on the was. It was already mounted onto the C-120! How lucky was that? Again thank you to all that responded and pointed me in the right direction.

[oliver2-44 9,759]

You got aa good deal!