wallfish 17,004 #1 Posted April 4, 2022 So it's been a while since the parts pile has been picked and piled up for some assembly of something/anything. Been get'n the urge to build something for a long while now so here we go again. Hopefully something new to bring to the big show. This was a project @19richie66 started a long time ago and it's about time it got some luv. The most difficult part for me is just getting it started. But typically once it gets going, time is then somehow found to put into it. -Probably gonna make this a fast one and use low 2nd or 3rd for cruise'n shows. -Front suspension and possibly rear suspension too if my idea works. 8 8 Share this post Link to post Share on other sites
Achto 27,594 #2 Posted April 4, 2022 Here to watch the master at work. 6 1 Share this post Link to post Share on other sites
19richie66 17,508 #4 Posted April 4, 2022 Can’t wait to see what you do with it. It’s in good hands. 👍 6 Share this post Link to post Share on other sites
953 nut 55,281 #5 Posted April 4, 2022 Will there be a snow plow blade used? I think I know where you could find one. 10 Share this post Link to post Share on other sites
wallfish 17,004 #6 Posted April 4, 2022 3 minutes ago, 953 nut said: Will there be a snow plow blade used? I think I know where you could find one. It's certainly possible and there's a couple already in stock. That's kinda my signature 2 seater style so we'll see 4 1 Share this post Link to post Share on other sites
Pullstart 62,905 #7 Posted April 4, 2022 (edited) So… who made the trip to gather it, drop it off, or meet in the middle? Edited April 4, 2022 by Pullstart Together… to gather… 2 Share this post Link to post Share on other sites
BHunter 1,700 #8 Posted April 4, 2022 I’m looking forward to seeing what you do with it. 2 Share this post Link to post Share on other sites
ri702bill 8,327 #9 Posted April 4, 2022 Not a big fan of using roller chain to turn the Unidrive unless there is an intermediate shaft that is belt driven or use a torque limiting slip clutch with the chain drive. The belt can slip - it is the safety valve if you would - the chain cannot. Bill 1 Share this post Link to post Share on other sites
ebinmaine 67,553 #10 Posted April 4, 2022 8 hours ago, Achto said: Here to watch the master at work. That's about what I was thinking too. 8 hours ago, wallfish said: Front suspension Super curious to see how that works. 2 Share this post Link to post Share on other sites
SylvanLakeWH 25,594 #11 Posted April 4, 2022 Save some popcorn @ebinmaine!!! 2 Share this post Link to post Share on other sites
ebinmaine 67,553 #12 Posted April 4, 2022 46 minutes ago, SylvanLakeWH said: Save some popcorn @ebinmaine!!! It's a big bucket Jim. I've got extra to share. 1 1 Share this post Link to post Share on other sites
ebinmaine 67,553 #13 Posted April 4, 2022 @wallfish Whatcha got for an enginemotor in there? 1 1 Share this post Link to post Share on other sites
Pullstart 62,905 #14 Posted April 4, 2022 1 hour ago, ebinmaine said: @wallfish Whatcha got for an enginemotor in there? Got allyer bases covered there? 2 2 Share this post Link to post Share on other sites
ebinmaine 67,553 #15 Posted April 4, 2022 2 minutes ago, Pullstart said: Got allyer bases covered there? Yes sir I did. Good catch. 1 1 Share this post Link to post Share on other sites
Ed Kennell 38,198 #16 Posted April 4, 2022 3 hours ago, ri702bill said: Not a big fan of using roller chain to turn the Unidrive unless there is an intermediate shaft that is belt driven or use a torque limiting slip clutch with the chain drive. The belt can slip - it is the safety valve if you would - the chain cannot. Bill I never had a belt slip on any of my tractors. The safety slip clutch has always been between the rubber and the road. In fact, to test the drive train of new tractors, I chain them to a tree and make sure they can spin the tires. 3 2 Share this post Link to post Share on other sites
19richie66 17,508 #17 Posted April 4, 2022 11 hours ago, wallfish said: It's certainly possible and there's a couple already in stock. That's kinda my signature 2 seater style so we'll see It was in my original plan. 1 3 Share this post Link to post Share on other sites
Lee1977 6,663 #18 Posted April 4, 2022 32 minutes ago, 19richie66 said: It was in my original plan. If you used two and cut out most of the center of the second you can have complete fenders. 1 Share this post Link to post Share on other sites
SylvanLakeWH 25,594 #19 Posted April 4, 2022 3 hours ago, ebinmaine said: @wallfish Whatcha got for an enginemotor in there? Isn’t it motorengine? 2 Share this post Link to post Share on other sites
Pullstart 62,905 #20 Posted April 4, 2022 1 hour ago, SylvanLakeWH said: Isn’t it motorengine? it deep ends if you start it then it runs or if it runs then you start it. I think. 1 2 Share this post Link to post Share on other sites
Ed Kennell 38,198 #21 Posted April 4, 2022 2 hours ago, SylvanLakeWH said: Isn’t it motorengine? Didn't we settle this last week? 1 4 Share this post Link to post Share on other sites
WHX?? 48,823 #22 Posted April 4, 2022 Evidently not Ed... Me thinks Sylvia is covering all the bases.... 1 1 Share this post Link to post Share on other sites
Lee1977 6,663 #23 Posted April 4, 2022 1 hour ago, Ed Kennell said: Didn't we settle this last week? sulvanLakeWH is just confused he has both Motors runs with electricity. Engines runs with gas, diesel, kerosene, alcohol, propane, natural gas, things that burn. Yes. it can be used interchangeable, those people just don't know what they are talking about. 1 1 Share this post Link to post Share on other sites
oliver2-44 9,756 #24 Posted April 4, 2022 I could see some ak-ak machine gun barrels sticking out those side hood scoops. Them hide some LED lights in the gun barrels. I've thought about widening a rear fender like that one has started. I'm interested to see how you finish it back together. Of course I would need a fender to widen, I'm 2 short as it is 2 Share this post Link to post Share on other sites
wallfish 17,004 #25 Posted April 4, 2022 8 hours ago, Pullstart said: So… who made the trip to gather it, drop it off, or meet in the middle? At the big show a while ago 1 hour ago, ri702bill said: Not a big fan of using roller chain to turn the Unidrive unless there is an intermediate shaft that is belt driven or use a torque limiting slip clutch with the chain drive. The belt can slip - it is the safety valve if you would - the chain cannot. Bill Last thing I want is the belt to slip there on the trans or any where else. That's part of the issue when speeding these up with using a small pulley on the trans and already been there a few times. There will be a jack shaft and belts between the engine and trans and maybe a torque converter . I have no problem at all using a chain there 1 hour ago, ebinmaine said: That's about what I was thinking too. Super curious to see how that works. Split axles off the sides of the frame rails and coil over shocks for the suspension 49 minutes ago, ebinmaine said: @wallfish Whatcha got for an enginemotor in there? 18 hp Onan B48 is set on there for now but could change. Thinking about using a drive shaft to a gear box, maybe. So it can be turned 90 deg. I do have a K321 14hp, K301 12hp, think there's also a 16hp out there and maybe another 8hp to pick from. I don't think a K91 would smoke those wide tires 5 hours ago, Lee1977 said: If you used two and cut out most of the center of the second you can have complete fenders. Had them mocked up like that in the past but the curve of the blade isn't an exact match for the radius of the tires and it kinda looked funny. However I may not keep it as tight to the tires this time but still thinking about it. Might look OK by cutting one in half length wise and going 1.5 blades 6 Share this post Link to post Share on other sites
