2022 Big Show buy, sell and trade.

[David Star 85]

I have a 520xi that I am wanting to sell at the big show. I have videos of it running that I can share. It runs very well and I also have the 52 in mower deck, a complete tiller setup and a dozer blade frame (that has a wee bit of a Bent blade).$1500 . I also have a two-state snow blower for the 5XI series, sold separately. $500

On 2/14/2022 at 3:39 PM, Pullstart said:

not for sale.  If you find one in this thread and pay for it in advance, I can haul it back to west Michigan 

 

Edited June 13, 2022 by David Star

[elcamino/wheelhorse 9,297]

@squonk Skunky save a single plug wire for me. Put a new one on the Waldomobile for free . He he

[squonk 41,104]

18 hours ago, elcamino/wheelhorse said:

@squonk Skunky save a single plug wire for me. Put a new one on the Waldomobile for free . He he

That would ruin the patina! 

[adsm08 2,056]

On 6/11/2022 at 11:14 AM, rjg854 said:

This is what I've got.

Overall length 17 3/4"

2 1/2 " to where the tie rods fasten

It's already welded so you won't have to worry about roll pins.

 

 

Just got out to measure my steering shaft. The dimensions appear correct.

[adsm08 2,056]

Assorted K181 parts. A few tins, a flywheel and stator, starter, valve cover (I think), and a few coils. All of it worked, as far as I know, except the coils, they are of unknown quality. The majority of it came off an engine I bought from @76c12091520h that was out of a 72 Raider.

No idea what these items are worth, will accept any reasonable offer.

 

 

I also have a 71 800 Special. Runs, drives, plows, engine is good and strong but it pops out of 3rd, E-clutch is getting worn out fuel shutoff valve leaks. Has a mule drive, and a snow plow. Rear tires are only 2 years old. I have the front hub caps and the face plate for the hood somewhere. Not bringing it to the show, unless someone wants it because it will boot one of the ones I want to show off the trailer.

$300 OBO

 

Lastly, a set of decals, the "C-160 8-speed" has a little damage, and may or may not be useable. The rest appear intact.

These were given to me by a co-worker who found them in his garage. Free to a good home.

 

EDIT: Starter and lens are gone.

Edited June 15, 2022 by adsm08

[JoeM 7,874]

@adsm08 $20 for the k181 starter

and I can use the lens in the last pic. 

 

Edited June 15, 2022 by JoeM

[adsm08 2,056]

10 hours ago, JoeM said:

@adsm08 $20 for the k181 starter

and I can use the lens in the last pic. 

 

 

Deal, starter and lens are sold.

[rjg854 11,361]

14 hours ago, adsm08 said:

 

 

Just got out to measure my steering shaft. The dimensions appear correct.

So you want me to bring this along with me?

[adsm08 2,056]

4 minutes ago, rjg854 said:

So you want me to bring this along with me?

Yes please.

[rjg854 11,361]

14 minutes ago, adsm08 said:

Yes please.

it's yours, look for it at Squonk's hospitality canopy.

[squonk 41,104]

@adsm08 I'll have the seat for your son's Speed-X as well.

[adsm08 2,056]

4 minutes ago, rjg854 said:

it's yours, look for it at Squonk's hospitality canopy.

 

1 minute ago, squonk said:

@adsm08 I'll have the seat for your son's Speed-X as well.

 

Thanks guys.

[Pullstart 62,851]

I still have some 42” snow plows and axle bracket  and A 48” 520 plow with extension bracket for sale.  These will not make the trip unless sold prior to leaving.

 

Also, an Xi front mule drive.  $75

 

 

[Pullstart 62,851]

GT14 plastic tank and two ‘69 (I believe) grille shells.  The tank has some heat damage but is intact.  The outlet nipple is in good shape.  
 

$65 for the shell without lights, $75 for the grill with lights.

 

$85 for the tank.

 

 

[Pullstart 62,851]

GT14 / ARK loader subframe brackets and front support/pump mount.  The right side has been torched a bit but appears to function just fine.

 

$225

 

I used a picture from one of @953 nut’s GT14 FEL posts for an example.  I also have the horizontal top pieces of the ARK frame I can toss in.  They were sawed off and would need to be welded onto the FEL uprights.

 

 

[Pullstart 62,851]

Original Nelson Muffler.  Looks like it fits a C series.  Has a bit of rattle in it, but is good and solid.  Asking $150

 

 

[Pullstart 62,851]

One more GT14 fuel tank.  And grille shell

 

No visible blemishes on the tank, it’s currently on Colt my GT14.  $100

 

Shell $85 with light bucket.  The lights even work!

 

 

[zigzag 127]

Hey guys  I've got two metal wheel weights for 10 inch wheels. 46.5 lbs each. $100. Sold. 

Edited June 16, 2022 by zigzag

[dalez 137]

53 minutes ago, zigzag said:

Hey guys  I've got two metal wheel weights for 10 inch wheels. 46.5 lbs each. $100.

If that's $100 for both I will take the weights.

Edited June 16, 2022 by dalez
add

[zigzag 127]

4 minutes ago, dalez said:

If that's $100 for both I will take the weights.

Yep. I'll bring them along for you. 

[BHunter 1,700]

I’m bringing a couple of tractors to sell for a friend of mine. He has a C101 with a bucket on it and a Black hood tractor that I restored. They both run and drive good. If interested I can get more info for you

[BHunter 1,700]

I’m selling a 1077 . It has a 12hp in it. Runs and drives great.  Has a deck too. 

[WHX?? 48,815]

What's he got on the ticket on the one with the FEL Bob ? Nice lookin rig I'd darn near be tempted to bicycle out and drive it back. 

Edited June 16, 2022 by WHX??

[RJ Hamner 1,007]

Any prices??

[BHunter 1,700]

15 minutes ago, WHX?? said:

What's he got on the ticket on the one with the FEL Bob ? Nice lookin rig I'd darn near be tempted to bicycle out and drive it back. 

I think it’s around 3k. 
That’s a long bicycle ride lol.