2022 Big Show buy, sell and trade.

[Mike'sHorseBarn 2,998]

50 minutes ago, oliver2-44 said:

@Mike’HorseBarn  I’m not going to the show, but It sure would be nice to have that HH55 for my Suburban project. I currently have an Hh60. Would you consider it claimed and Maybe I can find someone to Pony Express it Texas Direction, or as a last resort would you ship it to me on my dime of course.  

 

It's yours! Shoot me a pm and we can work out the details. 

[rjg854 11,356]

17 hours ago, adsm08 said:

I'm looking for a steering gear and shaft to fit an 855, preferably without worn roll-pin holes.

This is what I've got.

Overall length 17 3/4"

2 1/2 " to where the tie rods fasten

It's already welded so you won't have to worry about roll pins.

[adsm08 2,046]

2 hours ago, wallfish said:

I can't tell from the cryptic reply posts if someone actually claimed this engine or not. If you want please state that, if you don't please don't post about the possibility of someone you know who may want it.

Seems Adams dad might want it but Jennifer seemed like she was just too late after his post but never actually stated if she wants it.

SO, if this engine has not been actually claimed then I'm interested in it and will be at the show and will take it. If the others before me want it, could you please clearly claim it?

(Also wish people would stop quoting all of the pictures each and every time over and over. It makes following and reading through threads more difficult and long. You can simply delete those pics before submitting or just highlight the specific words you want to quote and the quote button will appear.)

Well, it seemed that way anyway but it's difficult to know for sure huh?

 

EDIT-- Seems @oliver2-44 posted at the same time and beat me to it.

 

I'm not going to claim it at this point, because it will be at least tomorrow night until I can talk to him about it, and if it won't work for his project I have no use for it.

[adsm08 2,046]

1 minute ago, rjg854 said:

This is what I've got.

Overall length 17 3/4"

2 1/2 " to where the tie rods fasten

It's already welded so you won't have to worry about roll pins.

 

Ok. I will have to get measurements from mine when I get home, or browse the manuals and try to compare part numbers.

[rmaynard 15,434]

Sundstrand Hydrogear

90-2019

875, 1075, 876 others.

Complete. Unknown condition. Would like to  trade.

This thing is heavy. I will only load it on the trailer and bring it if I have a commitment from someone. Any reasonable trade will be considered.

Contact me via PM 

 

 

 

 

 

 

 

 

 

Edited June 11, 2022 by rmaynard

[roadapples 6,983]

I have 2 Raider 10 6 speeds for sale. First one is 1972 with Kohler. New exhaust valve, intake valve dressed, 1 new pulley in mule drive, new bearing in other, new fuel lines, filter, electric fuel pump, plug, blades sharpened ready to mow. Little puff of smoke at start up...$375

Second is a 1968 with Techy. I did have it running when I got it, now no spark. $200. Tins are near perfect on both these tractors.

[Jennifer 1,877]

21 hours ago, Mike'sHorseBarn said:

 

Well no one has come right out and claimed so it's still available.

I missed this message!  🤷🏻‍♀️   It happens…

[76c12091520h 3,608]

  Kohler K??? engine , removed from a 1077. One owner tractor, here's the story : original owner claims that it had a 12 HP or 14HP short block installed a few years ago, has K301 stampings on the side of the block.....That being said, it runs great, carb shafts are tight, starter generator works as it should. I drove this tractor and the engine was strong. See attached video. $200.00       SOLD

Edited June 12, 2022 by 76c12091520h

[squonk 41,051]

Looking for a big block engine shroud for starter gen engine with all the holes to mount the coil,belt guard ect as opposed to this one that doesn't! . 

 

 

 

[buckrancher 2,679]

5 hours ago, squonk said:

Looking for a big block engine shroud for starter gen engine with all the holes to mount the coil,belt guard ect as opposed to this one that doesn't! . 

 

 

 

mike will one off a 1054 work?

[Ed Kennell 38,114]

One set of NOS 101335 mower blades.       Fits 36" SD and RD decks from the "70s.          $75 delivered to the Big Show or shipped to lower 48 for $100.

 

[squonk 41,051]

52 minutes ago, buckrancher said:

mike will one off a 1054 work?

Should Brian. I ' m putting a 14 HP on my 953 and I want to leave the engine on it now intact. I would have to drill 1 hole and weld a nut on the inside as opposed to about 6 with the shroud I have now. 

[Ed Kennell 38,114]

Kohler Command air filters.        CH 18-23 and CV 17-23    $15       CHCV25-27  and Command pro CH18-30   $20       delivered to the show.

[stevebo-(Moderator) 8,330]

All original and complete 953 engine. Locked up. $125 delivered to the show.

 

Complete and 1054. Bought from rs member several years ago. Was told it ran well. $250 delivered to the show

 

Nice 8 speed tranny. Only issue hubs were drilled and through bolted with correct lug nuts and brake band missing $225 delivered to the show

 

RJ front axle and spindles and linkage rod. $50 to the show SOLD TO DARENW 85

 

original 953/1054 snow plow bracket $100 delivered to show

 

c125 kohler 12 rubber mounted motor. Ran good when pulled off machine. Some parts have been removed. $175 to the show.

 

nice original 953 mower deck complete and patina. 200 to the show. 
 

spike aerator nice original patina. 100 to the show. 
 

1054/953 hydro pump $150 

gas tank for 954/1054 with wooden cradle $80 to the show 

[Ed Kennell 38,114]

New starters.      Mega Fire 435-300 fits Briggs & Stratton 7,8,10,12,12.5,16, and 18 HP       $75 delivered to the show.

6

 

Xtreme #691564 starter.  Fits Briggs & Stratton Vanguard 18-22HP     $90 delivered to the show.

 

Kohler starter #20-098 11S      Fits many KS and KV series Kohler engines            $75   delivered to the show

 

 

 

 

 

Edited June 12, 2022 by Ed Kennell

[Ed Kennell 38,114]

Stens  510-347 connecting rod       Fits K301 and K321   before S/N 172500013      0.010" under size crank    long dipper       $20 delivered to the show                    

 

 

[elcamino/wheelhorse 9,297]

ED , you run out of magic buckets yet ?

[Darrenw85 605]

Steve,

@stevebo, I'll take the RJ axle,.

 

Thanks,

Darren

[Mike'sHorseBarn 2,998]

Looking for a nice nice set of front wheels with this tire pattern for my c-160. 

 

 

[76c12091520h 3,608]

 I have available 2  NOS batteries, Toro / Wheel Horse era , that would be the perfect finishing touch on that  300 , 400, or 500 series restoration or display piece . Both batteries are dry ( no acid ) so they are perfect for display or just add acid and charge them up. $60.00 each. 

[Ed Kennell 38,114]

NOS ignition modules.   Fit XT149 model engines                                        $20 each delivered to the show.

[josephvigg 88]

Anyone from NJ or Local to NJ going to the big show?? 

 

Sadly don't think ill make it this year - who knew having kids would be so much work? - but if there is someone from the area that is going and is willing to keep an eye out for a good running rear engine mower they can bring back with them id be happy to pay for the help. Cosmetic not as important as function. I want to actually mow with it. Just a shot in the dark Thanks! 

Edited June 13, 2022 by josephvigg

[josephvigg 88]

On 6/7/2022 at 10:12 AM, Handy Don said:

 

Show Flyer: 

Thank You 

[squonk 41,051]

I'll have plug wires for sale:

 

Kohler Single $10

 

Kohler Twin  $ 18 Set

 

Onan Twin  $28   Set

[Handy Don 12,204]

I'll be bringing a 702 hood (also fits 552, 502 as well as Lawn Rangers 32E, 32R, 33E, and 33R)

I'll be looking to buy an 854 hood.

 

Edited June 13, 2022 by Handy Don