GT14 Deck Question

[richmondred01 2,237]

I’m not up on my GT knowledge.

Will the RL-486 deck function on the GT series or is it a different animal altogether?

Thanks. 

Edited December 6, 2021 by richmondred01

[Pullstart 62,809]

I believe the GT-14 deck has specially spaced gauge wheels to avoid the rear tires of the tractor.

[gwest_ca-(File Mod) 11,035]

If you follow the models this is what shows up.

Mower DNA 48" side discharge

1966-1967 model RL-486 replaced by

1968 model 5-1481

1969 model 5-1482

1970 model 5-1483

1971 model 5-1200

1972 model 5-1201

1973 model 5-1202

1973-1974 model 5-1210

1975 model 5-1211

1976 model 65-48MS01

1976 model 65-48MS02

1977 model 75-48MS01 - These all used blades with 5/8" x 3/4" double-D center hole unless the spindles have been upgraded.

-------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Note - 3/4" or .750" is 19.05mm

1977 model 75-48MS02 - Uses 6203 bearings with 3/4" ID - (First deck to use blades with 3/4" center hole) - Originally had a nylon-insert nut holding spindle pulley on.

1978 model 85-48MS01 - Uses 6203 bearings with 3/4" ID - Originally had a nylon-insert nut holding spindle pulley on.

1979 model 95-48MS00 - Uses 6203 bearings with 3/4" ID - Originally had a nylon-insert nut holding spindle pulley on.

1979 model 95-48MS01 - Uses 6203 bearings with 3/4" ID - Originally had a nylon-insert nut holding spindle pulley on.

1980 model 05-48MS01 - Uses 6203 bearings with 3/4" ID - Originally had a nylon-insert nut holding spindle pulley on.

1981-1983 model 05-48MS02 - Uses 6203 bearings with 3/4" ID - Originally had a nylon-insert nut holding spindle pulley on.

1984 model 05-48MS03 - Uses 6203 bearings with 3/4" ID - Originally had a nylon-insert nut holding spindle pulley on.

 

Note - 17mm is .669"

1985 model 05-48MS04 - Uses 6203 bearings with 17mm ID - Originally had a standard nut and lockwasher holding spindle pulley on.

1986-1988 model 05-48MS05 - Uses 6203 bearings with 17mm ID - Originally had a standard nut and lockwasher holding spindle pulley on.

1987-1988 model 05-48SC01 - Uses 6203 bearings with 17mm ID - Originally had a standard nut and lockwasher holding spindle pulley on.

1989 model 15-48SC01 - Uses 6203 bearings with 17mm ID - Originally had a standard nut and lockwasher holding spindle pulley on.

1990 model 15-48SC02 - Uses 6203 bearings with 17mm ID - Originally had a standard nut and lockwasher holding spindle pulley on.

1991-1992 model 15-48SC03 - Uses 6203 bearings with 17mm ID - Originally had a standard nut and lockwasher holding spindle pulley on.

1993-1997 model 78360 - Uses 6203 bearings with 17mm ID - Originally had a standard nut and lockwasher holding spindle pulley on.

1998-2007 and 2009-12 model 78361 - Uses 6203 bearings with 17mm ID - (These all use blades with 3/4" center hole) - Originally had a standard nut and lockwasher holding spindle pulley on.

[richmondred01 2,237]

Thanks for the info guys. 
Those GT’s are unique. 

[gwest_ca-(File Mod) 11,035]

The deck sold in 1969 for the GT-14 was 5-1482.

[richmondred01 2,237]

Thanks.