CrossThread Industries 31 #1 Posted October 10, 2021 Hello from the Mid Hudson Valley, Everybody... I was looking for a tractor for hauling out small to medium roots, haul some large wooden frames from a garage, and do some snow removal. After lurking around on all the familiar outlets like craigslist and facebook marketplace ( I have given up on eBay some time ago, except for parts) I settled in on Wheel Horse. There seems to be a fare basis of them around the NY, CT area. I picked up one from craigslist today, a 416-8 that undoubtedly been ridden hard and put away wet, but it runs, and it is paid for. The gent I bought it from makes a bit of a market in them and I ended up with an extra set of wheels, 55lb wheel weights, and some extra parts. I will go back for a mower deck, plow, and/or snowblower. Glad to be here and see you around... PJ 5 9 Share this post Link to post Share on other sites
Ed Kennell 38,241 #3 Posted October 10, 2021 to the PJ. Lotta folks on here ready to help if you have any questions. Share this post Link to post Share on other sites
8ntruck 7,021 #4 Posted October 10, 2021 Pretty good choice. to the forum. Good bunch of folks here. Whatever you happen to break, somebody on the forum has broken, and fixed, the same thing. They will be willing to share information and advice. Share this post Link to post Share on other sites
Herder 2,354 #5 Posted October 10, 2021 I am across the way from you. Judging by the one picture, it doesn't look that bad. Best of luck. Share this post Link to post Share on other sites
ebinmaine 67,672 #7 Posted October 10, 2021 Welcome to the addiction. These are fantastic machines. The more you do with it the more you'll be impressed. If you're not too careful you may even make a friend or two. We have Meet n Greets to get together and say hi. One coming up fairly local to you. 1 Share this post Link to post Share on other sites
Pullstart 62,917 #8 Posted October 10, 2021 Cross Thread! We’ve all been there, done that for sure Nice machine, and be careful they tend to multiply Share this post Link to post Share on other sites
peter lena 8,639 #9 Posted October 10, 2021 @CrossThread Industries , nice pick up on that , think your most important thing to do is a thorough BASELINE SERVICE , verify what works and doesn't work ,enhance every function , total lubrication of every movement point , engine and trans oil flush and refill . new shifter boot , drive belt replace. I personally would give that a aerosol lubricant rub down till dry to stop rust and retain patina . good luck , pete Share this post Link to post Share on other sites
Stormin 9,981 #11 Posted October 10, 2021 (edited) to from over the Pond. Pete. Edited October 10, 2021 by Stormin Share this post Link to post Share on other sites
Bill D 1,926 #13 Posted October 10, 2021 Welcome. I live in Poughkeepsie and also have an Onan powered horse. If I can help, please let me know. Share this post Link to post Share on other sites
Brockport Bill 1,668 #14 Posted October 11, 2021 Welcome neighbor --- I sent you a p.m. to open.. Bill Share this post Link to post Share on other sites
Brockport Bill 1,668 #15 Posted October 11, 2021 18 hours ago, ebinmaine said: Welcome to the addiction. These are fantastic machines. The more you do with it the more you'll be impressed. If you're not too careful you may even make a friend or two. We have Meet n Greets to get together and say hi. One coming up fairly local to you. where and when is the "local" Meet and Greet" you refer to? 1 Share this post Link to post Share on other sites
Bill D 1,926 #16 Posted October 11, 2021 October 23 @stevebo house in CT. 1 Share this post Link to post Share on other sites
ebinmaine 67,672 #17 Posted October 11, 2021 3 hours ago, Brockport Bill said: where and when is the "local" Meet and Greet" you refer to? 45 minutes ago, Bill D said: October 23 @stevebo house in CT. Steve's a great host with an excellent place to get together. Trina and I went 4 years ago and have been trying to get back there for several years now. If all goes according to plan we'll be attending. Share this post Link to post Share on other sites
johnnymag3 2,520 #18 Posted October 11, 2021 Welcome to the BEST Wheel Horse Forum on the Planet !!!! I live very close to you, in the Clinton Corners, Millbrook area and will share thoughts and ideas anytime !!!! Share this post Link to post Share on other sites
953 nut 55,325 #19 Posted October 11, 2021 On 10/9/2021 at 9:45 PM, CrossThread Industries said: Glad to be here and see you around.. Glad to have you hear with us and look forward to more as you start adding implements. Wheel weights and chains will make your a real snow removal beast. Liquid filled tires is another way to gain traction without breaking the bank. Share this post Link to post Share on other sites
echris 1,425 #20 Posted October 16, 2021 (edited) Hey Pete and welcome. Another Hudson Valley WH nut added to the family. I'm right down the road from you. Good luck with your new machine. You're going to love it. Especially when you start working on it and marvel how simple it is to repair most anything. And the folks here are always ready to lend advice, parts, whatever you need. Good call! Edited October 16, 2021 by echris Share this post Link to post Share on other sites
