22x9-12 Tire

[TC10284 111]

I need to replace a tire on a 312-8. The ones on it now are 22x9.00-12. All I can find online is 22x9.50-12

Where are you guys getting them? Or do I need to just get two 22x9.50-12?

 

I could probably get by with a tube, but even having trouble locating one of those in that size. 

Edited October 3, 2021 by TC10284

[Pullstart 63,632]

A 23x__-12 is typically easier to find, and still fits.  That tends to be the route most people take, be it 8 or 10” wide.

[Sparky-(Admin) 21,775]

  If your looking for a perfect match, both size and tread pattern, try posting a wanted ad in our classifieds. 
  Include your location and a pic of the tire tread.

 

[Maxwell-8 4,366]

My Aunt runs 23x10.50-12 on her 312-8

Edited October 3, 2021 by Maxwell-8

[cschannuth 3,817]

23X10.50 Deestone will be similar size as that 9.50.   They are in expensive and good tires.

[TC10284 111]

I was hoping to avoid having to get two new rears. Would I notice much height difference if I went with a 22x9.50-12? Half an inch width would be the obvious answer. Wondering if I'd notice that when mowing or otherwise. 

Edited October 3, 2021 by TC10284

[Sparky-(Admin) 21,775]

  22” is the height and 9 or 9.5 is the width so in theory you would see no difference in height. That being said, a 22” or 23” tire will vary in height between brands. This applies to widths as well. 
  I still say try to find a good used one. You could probably find one on a rim and not incur dismounting and remounting cost. Just bolt it on!
  
  

[Thor27 828]

1 hour ago, TC10284 said:

I was hoping to avoid having to get two new rears. Would I notice much height difference if I went with a 22x9.50-12? Half an inch width would be the obvious answer. Wondering if I'd notice that when mowing or otherwise. 

 

Age probably has more to do with it than we give it credit for, I have had tires from the same manufacturer with the same size on the sidewall measure very differently with the only difference being age.

Manufacturers have been down sizing products to save money in manufacturing.. That is the risk in attempting to replace one..

. 

[Lee1977 6,936]

I have two 23 x 950 x 12  2 ply's that I will give you that came Off the back of my 1989 520. One had a tube in it you can have the tube also..

They round up in the center when they have enough air to hold up the tractor didn't like the way they look. I'll PM my address if you want to come get them.

Edited October 3, 2021 by Lee1977

[TC10284 111]

13 hours ago, Lee1977 said:

I have two 23 x 950 x 12  2 ply's that I will give you that came Off the back of my 1989 520. One had a tube in it you can have the tube also..

They round up in the center when they have enough air to hold up the tractor didn't like the way they look. I'll PM my address if you want to come get them.

 

Looks like you're in Rockwell. About 30min from me. 

Yeah I'd be interested sir. Thanks! 

 

[Pullstart 63,632]

To answer your question a bit about the 9 v. 9.5 width, a little air pressure adjustment could compensate for any wedge you put in the tractor due to any slight height differences.  Y’all should know that, you’re in NASCAR country!  

[TC10284 111]

 

Thanks sir!

Not sure when I'll be able to get down there, but I'll call you before to find out of course. 

[Handy Don 13,125]

1 hour ago, Lee1977 said:

 

Rockwell NC 28138

 

 

Lee

Hello,

Gonna strongly suggest NOT putting your info in regular posts--this site is wide open on the internet and regularly scanned by search engines (Bing, Duck Duck Go, Google, etc.)

We use the Personal Messages channel for that (click on th the member to the left of their post to see their profile and then use the "message" button.

 

Asking a moderator, @Sparky, @stevasaurus, to remove posts #12 and #13.

Thanks

Edited October 4, 2021 by Handy Don

[stevasaurus 22,972]

Taken care of.  I hid the post with the information in it.