657/867/1267 clutch idler pulley?

[ebinmaine 67,618]

@OldWorkHorse Steve and I both need a clutch idler pulley on early tractors. 

 

The one from Trina's 856 military tribute tractor measures 3" od. 

 

How do we get these new?

 

Is there a Sten's or other aftermarket number?

 

Edited April 30, 2021 by ebinmaine

[stevasaurus 22,764]

Well Eric, you could try our "Classified / Wanted" Section.  A-Z, etc.  

[ebinmaine 67,618]

4 minutes ago, stevasaurus said:

Well Eric, you could try our "Classified / Wanted" Section.  A-Z, etc.  

😀

 

Oh.. I know.  

In fact Lincoln was my first thought.

 

I'll edit my first post. I was hoping for a part number from some place like Sten's or an alternate source for new ones.

 

I need one and I want to put one in stock and I know Steve needs one too. 

 

[Pollack Pete 2,273]

Anything at Tractor Supply? I've seen various pulleys there.Just a thought.

[squonk 41,155]

30 minutes ago, ebinmaine said:

@OldWorkHorse Steve and I both need a clutch idler pulley on early tractors. 

 

The one from Trina's 856 military tribute tractor measures 3" od. 

 

How do we get these new?

 

Is there a Sten's or other aftermarket number?

 

Eric, PM @prondzy

[elcamino/wheelhorse 9,326]

@ebinmaine Try K & B just bought 2 deck idler pulleys from him.  There was a guy on here a couple of years ago that had a boat load of pulleys for sale. You may want to do a search.

[EricF 589]

16 minutes ago, Pollack Pete said:

Anything at Tractor Supply? I've seen various pulleys there.Just a thought.

I was able to track down a pulley for a Bolens deck at TSC a while back. Correct pulley diameter and shaft size, but the overall thickness of the pulley due to heavier-gauge metal made it too thick to put the top shroud back on over it; had to run it exposed. May or may not be an issue for you; check your clearances under the belt shroud if you think they have a match.

[stevasaurus 22,764]

Waldo, I remember seeing all those pulleys that guy had...they were Wheel Horse pulleys also.  Right, about 2 years ago in the For Sale Classifieds.  

[squonk 41,155]

@prondzy rebuilds them.

[oliver2-44 9,760]

I got some rebuilt by Prodzy. Very 👍🏾 

[Pollack Pete 2,273]

Just tried a Google search for 3 in. OD idler pulley.Lots there.What size center hole do you need?

[pfrederi 17,741]

867 use pulley 1623 now 92-7102 only $45

Edited April 30, 2021 by pfrederi

[ebinmaine 67,618]

14 minutes ago, pfrederi said:

867 use pulley 1623 now 92-7102 only $45

"Only".....

I don't mind spending money on something when I need to but I'm too damn cheap to spend $45 on a pulley...

 

Between Steve and I we need 4. 

Edited April 30, 2021 by ebinmaine

[ebinmaine 67,618]

58 minutes ago, Pollack Pete said:

Just tried a Google search for 3 in. OD idler pulley.Lots there.What size center hole do you need?

Thanks Pete. I'll check it out when I get home. I think it's 3/8?

 

Looks likely that we'll order four of them from @prondzy. 

[ebinmaine 67,618]

1 hour ago, stevasaurus said:

Waldo, I remember seeing all those pulleys that guy had...they were Wheel Horse pulleys also.  Right, about 2 years ago in the For Sale Classifieds.  

Steve I looked on my phone which is of course different from a pc. My listings using a search term "pulley or pulleys" only go back maybe six or seven months? I couldn't figure out how to go any further than that.

 

[elcamino/wheelhorse 9,326]

@stevasaurus It was about 2 plus years ago.

[rjg854 11,387]

@greenbushtrees I think was his handle. I've bought a few different pulleys from him over the years. I don't think I've ever seen him post much.

[daveoman1966 3,752]

I have an ebay listing with the 1623 pulley.    I have TWO of these...$21.95 each + 5 ship.  

Ebay item : 133412177681

 

 

Edited April 30, 2021 by daveoman1966

[kpinnc 12,091]

I got one today at TSC for $19. 3 inch diameter with a 3/8 bearing. It will need a spacer on the mounting bolt, but that is easy enough.

Edited May 2, 2021 by kpinnc

[ebinmaine 67,618]

6 hours ago, kpinnc said:

I got one today at TSC for $19. 3 inch diameter with a 3/8 bearing. It will need a spacer on the mounting bolt, but that is easy enough.

Could you post pics please?

 

[kpinnc 12,091]

13 hours ago, ebinmaine said:

Could you post pics please?

I typoed that, it is 5/8 bore. I think the spacers are 3/4 but they have that size at TSC too.

Edited May 3, 2021 by kpinnc

[ebinmaine 67,618]

1 hour ago, kpinnc said:

I typoed that, it is 5/8 bore. I think the spacers are 3/4 but they have that size at TSC too.

@OldWorkHorse

Steve lookitt here. 

[OldWorkHorse 3,045]

If I get a min ill swing by there today and see what I can find. Got to go the metal place to and we know what happened last time I went to TSC and the metal store all in one day...

[Howie 886]

I always press the insert out of a wornout pulley and save them. A lot of them

have that bearing and an insert pressed into it. Sometimes have to shorten the

back side for alignment.

[Lane Ranger 10,968]

On 4/30/2021 at 2:23 PM, squonk said:

@prondzy rebuilds them.

 

I have had several rebuilt by @prondzy and you can’t beat his price and quality of work.  I save every old original 1623 riveted idler pulley.   Going to send them to Mike for rebuilds!