Here ~She~ goes again...

[Sailman 1,291]

WOW! What a great job you two! Amazing and creative restoration....

and the bike horn is great for grins!

[ebinmaine 67,408]

5 minutes ago, Sailman said:

bike horn is great for grins

Gotta have a horn!!!

 

[ebinmaine 67,408]

Front and rear lights are working.  

 

 

Love these Red White n Blue!! 

 

 

 

The @Wheel Horse 3D Grey made grenade shifters are in place.  

 

 

 

 

 

 

Here's a full scale model for comparison.  

[SylvanLakeWH 25,525]

Based on the relative general jewelanatomical location of them grenades, I'd triple check they ain't live... 

 

 

[ebinmaine 67,408]

1 minute ago, SylvanLakeWH said:

Based on the relative general jewelanatomical location of them grenades, I'd triple check they ain't live... 

 

 

 

 

 

 

The uhhhhh  jewelanatomical location will NOT be an issue given consideration that the owner/driver is a ♀️ woman girl female. 

 

 

 

[kpinnc 11,998]

12 minutes ago, ebinmaine said:

The uhhhhh  jewelanatomical location will NOT be an issue given consideration that the owner/driver is a ♀️ woman girl female. 

 

She may disagree with you Eb... 

 

They don't talk about theirs as much as us big strong manly chicken turds do, but that don't mean they don't care! 

[Wheel Horse 3D 3,791]

1 hour ago, ebinmaine said:

 

 

 

 

The uhhhhh  jewelanatomical location will NOT be an issue given consideration that the owner/driver is a ♀️ woman girl female. 

 

 

 

My personal pronouns are H.E.(might have to be an explosive geek to get that)

Edited May 4, 2023 by Wheel Horse 3D

[ebinmaine 67,408]

 

 

 

 

[kpinnc 11,998]

@ebinmaine

 

Somebody done stole your rear wheels! 

[Handy Don 12,210]

On 5/4/2023 at 11:47 PM, kpinnc said:

@ebinmaine

 

Somebody done stole your rear wheels! 

But they were kind enough to leave a couple of wheelbarrow wheels behind

[kpinnc 11,998]

3 hours ago, Handy Don said:

But they were kind enough to leave a couple of wheelbarrow wheels behind

 

So as not to completely strand you...

[Tractorhead 9,064]

Excellent job eric!👍

[Monstrosity 1,127]

Awesome work love it!!

[ebinmaine 67,408]

20 hours ago, Monstrosity said:

Awesome work love it!!

Thank you Thank you!!

 

@Pullstart thanks for posting the link to this. 🙂

[ebinmaine 67,408]

Thought you folks might get a kick outta the gorilla tape repair here. 

 

The "U" was lookin a bit "J"..

 

 

Off to Owl's Head !

 

 

 

 

[Moparfanforever 844]

Have a safe trip and nice looking tractors!!

[ebinmaine 67,408]

I could use a little help with the Starter Generator LIGHT folks. 

 

Trina's been using this tractor for several months now. No serious issues so far. 

When I wired it all up the S/G lamp was constant on. 

I figured the charging part wasn't working so Trina was popping the battery charger on the tractor about every 3 or 4 weeks from May to August. 

At one point she decided to see how long it would go between charges. That was 3 months ago so we believe it's charging correctly and that the lamp or wiring is the problem.  

 

How do I check the lamp to confirm operation?

If that's good, what's the proper wiring for it?

 

 

 

 

@953 nut @Achto

[953 nut 55,174]

2 hours ago, ebinmaine said:

How do I check the lamp to confirm operation?

If that's good, what's the proper wiring for it?

You can check the battery voltage at rest and while running at half throttle. If there is an increase in voltage your charging system is good to go.

It has been some time since you were doing the wiring so I don't remember if you used a solenoid or what light socket you used. The generator light should have two wires coming from it and neither one will be grounded, the Cole-Hersee  PL 20 RC is the correct socket. If you used a solenoid and 103-990 ignition switch with a Starter/Generator the drawing below is the one you want to follow. 

 

[ebinmaine 67,408]

We brought the Millie tractor in the basement workshop for some repairs and maintenance.  

 

Diagnosis on no-start or stall condition. 

 

Change ALL fuel line and filter. (The clear blue line was hardening too quickly for my satisfaction).

 

Increase upper RPM limit. 

 

Determine cause of generator lamp dysfunction as per last post.  

 

 

 

[ebinmaine 67,408]

Can anybody offer any tips or tricks for repairing stripped out bolt holes in the engine for where the sheet metal is supposed to be held on?

[SylvanLakeWH 25,525]

I had a mini bike that Dad cut thin tin strips and put in stripped holes to keep chain guard on... worked like a charm... poor man's tool and die... single use.

 

Not a "repair" but quick and functional. No pics... photography had just been invented... 

[Darrenw85 605]

I have run the next size tap in several of mine to fix the same problem. 

[Racinbob 11,048]

1 hour ago, SylvanLakeWH said:

I had a mini bike that Dad cut thin tin strips and put in stripped holes to keep chain guard on... worked like a charm... poor man's tool and die... single use.

 

Not a "repair" but quick and functional. No pics... photography had just been invented... 

 

I've tapped a few out to 5/16". Fine thread seems to work best. 

[wallfish 16,994]

3 hours ago, SylvanLakeWH said:

I had a mini bike that Dad cut thin tin strips and put in stripped holes to keep chain guard on... worked like a charm... poor man's tool and die... single use.

 

Not a "repair" but quick and functional. No pics... photography had just been invented... 

Ha, Toothpicks work for that! Learned from my grandfather. ( But -- depending upon what it's holding )

[ebinmaine 67,408]

8 hours ago, Darrenw85 said:

I have run the next size tap in several of mine to fix the same problem. 

 

7 hours ago, Racinbob said:

 

I've tapped a few out to 5/16". Fine thread seems to work best. 

 

Got this done tonight.