richmondred01 2,237 #1 Posted March 23, 2021 I’m all out. Anyone know where I can get one? Thanks. Share this post Link to post Share on other sites
953 nut 55,329 #2 Posted March 23, 2021 https://www.mcmaster.com/set-screws/extended-tip-set-screws/alloy-steel-extended-tip-set-screws-9/thread-size~1-4-20/ 3 1 Share this post Link to post Share on other sites
ebinmaine 67,693 #4 Posted March 23, 2021 Good reminder. I need some some too.... Share this post Link to post Share on other sites
richmondred01 2,237 #5 Posted March 23, 2021 Perfect. which part number would recommend? Share this post Link to post Share on other sites
pfrederi 17,741 #6 Posted March 23, 2021 I believe originals were 3/4" I use 1" 1/4 NC Share this post Link to post Share on other sites
953 nut 55,329 #7 Posted March 23, 2021 I use the one inch long screws, a bit longer than the units but the boot will cover it. 92505A542 is the part number. Shipping will be more than the parts but you are getting a bag of 25. 2 Share this post Link to post Share on other sites
pfrederi 17,741 #8 Posted March 23, 2021 Pick up some Axle set screws and The front wheel special hub bolts and make it worth while 3 Share this post Link to post Share on other sites
WHX?? 48,834 #9 Posted March 23, 2021 (edited) I got a but load of 3/4" I can send you a couple for the cost of a stamp. Prolly get them faster from MC tho than USPS these days. Quick story here when I was a green horn here (still am) and not having a clue Bob Parks sent me one to get me out of a jam.... he didn' even know me back then. Never forgot that so now I stock them and try to pay it forward. I buy in bulk now, give half to Dan for all the crap he does for me and tell him to make some friends too. Edited March 24, 2021 by WHX24 3 5 1 Share this post Link to post Share on other sites
richmondred01 2,237 #10 Posted March 24, 2021 1 minute ago, WHX24 said: I got a but load of 3/4" I can send you a couple for the cost of a stamp. Prolly get them faster from MC tho than USPS these days. Quick story here when I was a green horn here (still am) and not having a clue Bob Parks sent me one to get me out of a jam.... he didn' even know me back then. Never forgot that so now I stock them and try to pay it forward. I buy in bulk now, give half to Dan and tell him to make some friends too. That’s great. I will pm you. Thanks. Share this post Link to post Share on other sites
WHX?? 48,834 #11 Posted March 24, 2021 Your ......Get them out tommorow Richmond .... I'd throw in a couple of jam nuts but fresh out till next MC order. 1 Share this post Link to post Share on other sites
WHX?? 48,834 #12 Posted March 24, 2021 35 minutes ago, pfrederi said: Pick up some Axle set screws and Make mine stainless Paul! 1 Share this post Link to post Share on other sites
richmondred01 2,237 #13 Posted March 24, 2021 I sent you a pm. thanks again. 1 Share this post Link to post Share on other sites
WHX?? 48,834 #14 Posted March 24, 2021 (edited) Got ya covered guy... set them out so as is I don't forget ! Ya need more than two let me know I got six left but I know Dan is holdin. I think next time I order I will get the 1 inchers. The 3/4's seem to break right at the point of the allen end and at the worst time. 'Course this one has only been in use for what 50 some years? Edited March 24, 2021 by WHX24 2 Share this post Link to post Share on other sites
richmondred01 2,237 #15 Posted March 24, 2021 Thank you. Share this post Link to post Share on other sites
ebinmaine 67,693 #16 Posted March 24, 2021 9 minutes ago, WHX24 said: Got ya covered guy... set them out so as is I don't forget ! Ya need more than two let me know I got six left but I know Dan is holdin. Boys I could use a few here. Maybe 4?? Gladly pay ya pack for em. Share this post Link to post Share on other sites
WHX?? 48,834 #17 Posted March 24, 2021 14 minutes ago, ebinmaine said: Boys I could use a few here. Maybe 4?? Gladly pay ya pack for em. Yer on yer own sad sack.... nawww just kidding. .. well maybe NOT .......you might get two of them tho.... 1 4 Share this post Link to post Share on other sites
Achto 27,622 #18 Posted March 24, 2021 Jim, I'll take a look at my tranny hording stock. Let me know if you need some. 3 Share this post Link to post Share on other sites
WHX?? 48,834 #19 Posted March 24, 2021 15 minutes ago, Achto said: Jim, I'll take a look at my tranny hording stock. Let me know if you need some. Nawww... let's let EB stew abit... sides he... well he did send us some parts for a choice resto... nawww stew him abit more... 5 Share this post Link to post Share on other sites
Lane Ranger 10,968 #20 Posted March 24, 2021 Here is a broken set screw Lawnman_56. (Rodney Burger ) spent thirty minutes getting out of his 854! He used a pick to slowly turn the broken screw. I buy set screws from McMaster-Carr also but buy them one inch long instead of 3/4. The location of the set screws on top of the tractor tins and the Allen wrench inset are difficult to access. The extra length helps with jam nut and access for big fingers! 5 Share this post Link to post Share on other sites
squonk 41,164 #21 Posted March 24, 2021 (edited) I'm only replying to get the replies past 20! Unbelievable how much activity a set screw can cause. You'd think it was winter out and we were all stuck inside with a blizzard! Edited March 24, 2021 by squonk 1 3 1 Share this post Link to post Share on other sites
WHX?? 48,834 #22 Posted March 24, 2021 2 minutes ago, squonk said: how much activity a set screw can cause. Don't take much to entertain us I guess.... get to be some of our ages the other forms of adult entertainment are out the window.... 1 3 Share this post Link to post Share on other sites
oliver2-44 9,765 #23 Posted March 24, 2021 Me 3 4 1 Share this post Link to post Share on other sites
rjg854 11,389 #24 Posted March 24, 2021 Is everyone talking about a dog point screw Might as well get in on this 1 1 1 Share this post Link to post Share on other sites
Lane Ranger 10,968 #25 Posted March 24, 2021 (edited) If you ever had a problem with one you will never forget it and you will always be looking for some improvement! Just remember where your. dog point screw is going! Edited March 24, 2021 by Lane Ranger Editing script 1 Share this post Link to post Share on other sites
