Project "Snow Drift"

[Oldskool 6,644]

6 hours ago, Wheel Horse 3D said:

My only 2 thoughts are, maximum surface area to the ground,(minimize ground psi)

And ideal pitch for screw to balance ground torque against screw, vs forward momentum should be 45 degrees. A steeper pitch, while increasing forward thrust per rev, increases forces acting perpenndicular against the screw.

A lesser pitch looses forward momentum, but decreases that opposing torque.

I looked it over this morning it looks to be approx. 52 degree on the pitch. So I'm close to the 45 degree.

[Oldskool 6,644]

2 hours ago, Tractorhead said:

Another thing i found out when i searched a fitting hydraulic motor for my Sicklebar hedgecutter project,

the bigger the motor‘s the slower their output RPM.

 

when i do my equations, to estimate what i need on torque i use a torquewrend to get a feeling of what 

torque i will need estimated to work that thing.

therefore i get a 2 cm thick piece of woof i try to cut.

 

 

with the torquewrench on the sicklebar i try to find out, how much torque shall be enough to cut that.

after i got my value i double the result + adding 10%reserve for any unknown i may overseen.

 

On a sidenote:

That thing works like a charm and Hedgecutting is now a just act of Fun and Seattime instead before.

 

 

Because of the needed flow on the pump i would calculate both motors on max flow (peak) 

i like the idea of the flow divider. But that also consumpts a bit of the given input force.

i found on my search, that there exists a dual steering valve for such purposes but i missed the link.

This valvesystem with integrated divider wasn‘t much more expensive than a normal dual valve.

will do a research,i hope i find the source again.

That's a nice looking hedge trimmer. I could have used something like that last fall.

[Tractorhead 9,064]

Thanks,

that was 25 year old walk behind mower with a blown Briggs Engine i get for free.

 

because i hate it to trashing things and buy new, i do this rework to make me my life easier.

i had somewhere a Video of it in Action, but i missed the link for the moment.

 

[Wheel Horse 3D 3,795]

2 hours ago, Oldskool said:

I looked it over this morning it looks to be approx. 52 degree on the pitch. So I'm close to the 45 degree.

Lol like I said..yall pretty much have it covered!

[Oldskool 6,644]

Just now, Wheel Horse 3D said:

Lol like I said..yall pretty much have it covered!

Not all of it. It needs to go faster then a snail's pace 🤣🤣

[Wheel Horse 3D 3,795]

28 minutes ago, Oldskool said:

Not all of it. It needs to go faster then a snail's pace 🤣🤣

Still...freakin' EPIC thus far!

[Oldskool 6,644]

A new video is being uploaded now. Soon to come. Out for a joyride.

 

[Oldskool 6,644]

 

[ebinmaine 67,502]

AAWWEESSOOMMEE

[Tractorhead 9,064]

Great,

It appears to be a cool ride on Snow.

 

Instead of sinking, you be able to drive over the snow, so in my conclusion that‘s better than a bad walk in deeper snow,

even you feel it‘s slow. Improve can be done, no doubt, but i like it.

 

 

 

[wallfish 17,000]

Frigg'n Awesome!!! Thanks for sharing the video

 

 

[Handy Don 12,232]

8 hours ago, Tractorhead said:

On a sidenote:

That thing works like a charm and Hedgecutting is now a just act of Fun and Seattime instead before.

 

 

Did you try to create any sort of counter balance to reduce vibration?

[Handy Don 12,232]

Oops. double post

Edited February 21, 2021 by Handy Don

[wallfish 17,000]

13 hours ago, Handy Don said:

(I used 10mph in my spreadsheet but that may be too slow for some folks!)

Or too much for Oldskool's wallet LoL

Running the numbers like you do is great advantage compared to my WAG method.

[pfrederi 17,739]

Amazing I like the way it goes sideways.  Hope you don't suffer a break down or get stuck,  towing that home might need a  M 816 5 Ton Wrecker

 

 

Edited February 21, 2021 by pfrederi

[DennisThornton 4,769]

Impressive!  I'm very please to have been able to watch the build from the beginning!

[Oldskool 6,644]

1 hour ago, Tractorhead said:

Great,

It appears to be a cool ride on Snow.

 

Instead of sinking, you be able to drive over the snow, so in my conclusion that‘s better than a bad walk in deeper snow,

even you feel it‘s slow. Improve can be done, no doubt, but i like it.

 

 

 

I'm real happy with it all in all. I'm especially pleased with the articulation. 

[Oldskool 6,644]

1 hour ago, wallfish said:

Frigg'n Awesome!!! Thanks for sharing the video

 

 

Thanks for joining in on the fun.

[Oldskool 6,644]

1 hour ago, wallfish said:

Or too much for Oldskool's wallet LoL

Running the numbers like you do is great advantage compared to my WAG method.

Full hydraulics will be in the future. I at least have to get 10mph out of it. I cant let a Craftsman mower get by me 🤣🤣

[Oldskool 6,644]

1 hour ago, pfrederi said:

Amazing I like the way it goes sideways.  Hope you don't suffer a break down or get stuck,  towing that home might need a  M 816 5 Ton Wrecker

 

 

Sideways is the only way I can get it in and out of the garage over the cement. No doubt, I think it would take something like that  for recovery.

[Oldskool 6,644]

53 minutes ago, DennisThornton said:

Impressive!  I'm very please to have been able to watch the build from the beginning!

Glad you could join in. It's been fun.

[8ntruck 7,004]

I like it!  

 

Looks like maybe 2nd gear low range sort of speed.

[Oldskool 6,644]

24 minutes ago, 8ntruck said:

I like it!  

 

Looks like maybe 2nd gear low range sort of speed.

Ya pretty close to it I think.

[Ted Gardner 36]

The 816 is fine but a 88 would be more impressive! My hat is off to you sir. 

[Oldskool 6,644]

20 minutes ago, Ted Gardner said:

The 816 is fine but a 88 would be more impressive! My hat is off to you sir. 

Thank you