bigcreek 205 #926 Posted August 8, 2021 Like your trailer set up, I plan make similar set up. Planned to bring two to big show. But ran out of time to make the conversation from single to haul two. how does it go down the road like this, I’m going to use 2x12 pressure treated, with maybe a support brace under each if they sag. Share this post Link to post Share on other sites
ebinmaine 67,550 #927 Posted August 8, 2021 3 minutes ago, bigcreek said: Like your trailer set up, I plan make similar set up. Planned to bring two to big show. But ran out of time to make the conversation from single to haul two. how does it go down the road like this, I’m going to use 2x12 pressure treated, with maybe a support brace under each if they sag. Ramps I used are from HF. I've had it for a few years. Works great. I went with steel over wood when I built it because PT can be slippery and isn't as strong. It's VERY important to note that this trailer is COMMERCIAL grade. 3400 lb axle under it. Very well built framework. Share this post Link to post Share on other sites
bigcreek 205 #928 Posted August 8, 2021 This made me down double check I’ve got a 6x12, and it has a 3500# axle ill have to consider metal as well thanks 1 Share this post Link to post Share on other sites
D_Mac 8,619 #929 Posted August 8, 2021 Crusty with new tires and wheels. 3 2 Share this post Link to post Share on other sites
Gregor 4,846 #930 Posted August 8, 2021 How can you stand to have the things staring at you all the time. Would drive me bonkers. 2 Share this post Link to post Share on other sites
AMC RULES 37,130 #931 Posted August 8, 2021 Was trying a few different kid haulers on for size here today. 2 7 Share this post Link to post Share on other sites
squonk 41,136 #932 Posted August 8, 2021 Do you load an unload them with flip flops on ? 2 1 2 Share this post Link to post Share on other sites
ebinmaine 67,550 #933 Posted August 8, 2021 45 minutes ago, squonk said: Do you load an unload them with flip flops on ? Probably. Maybe 👟 sneakers. But we don't drive them on or off the trailer while in the seat so it's nice and easy to run our toes over. 4 Share this post Link to post Share on other sites
D_Mac 8,619 #934 Posted August 9, 2021 10 hours ago, squonk said: Do you load an unload them with flip flops on ? Maybe @pullstartshould get a pair of these. Steel toe flip flops. Yes they do exist. 1 2 7 Share this post Link to post Share on other sites
Pullstart 62,905 #935 Posted August 9, 2021 11 hours ago, squonk said: Do you load an unload them with flip flops on ? yes. 1 2 Share this post Link to post Share on other sites
Pullstart 62,905 #936 Posted August 9, 2021 Here’s a couple fun ones. 1 5 1 Share this post Link to post Share on other sites
AMC RULES 37,130 #937 Posted August 13, 2021 (edited) New York Steam Engine Association. 2021 Pagent of Steam. Edited August 13, 2021 by AMC RULES 10 Share this post Link to post Share on other sites
1940willys 120 #938 Posted August 14, 2021 AMC Rules, is this Steam Pagent in Alexander, N.Y.? I don't think that happened yet in 2021? Or, was there one in Canandaigua, N.Y? Share this post Link to post Share on other sites
Handy Don 12,232 #939 Posted August 14, 2021 9 minutes ago, 1940willys said: AMC Rules, is this Steam Pagent in Alexander, N.Y.? I don't think that happened yet in 2021? Or, was there one in Canandaigua, N.Y? This one is just east of Canandaigua. Share this post Link to post Share on other sites
Pullstart 62,905 #940 Posted August 14, 2021 It’s almost Saturday! We’ve been busy with life and a little bit of travel, but I sure miss putting around on some machines! 6 1 Share this post Link to post Share on other sites
WheelHorse520H 708 #941 Posted August 14, 2021 This is what I’ve got this week for side shots. The 520 is still in pieces and the 607 I just picked up Tuesday. 2 1 Share this post Link to post Share on other sites
peter lena 8,631 #942 Posted August 14, 2021 @cschannuth looks like sharp blades and a clean deck at the highest setting to me , I also regularly change my cutting pattern . when you are sharp and clean the results always look good . that goes along with regular cutting , good job on that , pete 1 Share this post Link to post Share on other sites
johnnymag3 2,520 #943 Posted August 14, 2021 C 120 getting ready for tear down, and refreshing........Not going to paint anything. Just going to clean it.... replace and give it NEW Hoses, Filters, Fluids, and any other mechanical thing thats looking too worn for duty... A nice seat is in its future also. SIDE SHOT FOR ME THIS WEEKEND !!!!! 4 5 Share this post Link to post Share on other sites
JCM 9,172 #944 Posted August 14, 2021 One of my favorites @johnnymag3 4 2 1 Share this post Link to post Share on other sites
ebinmaine 67,550 #945 Posted August 14, 2021 1 hour ago, johnnymag3 said: Like that phone number. RO 9- .... 5 Share this post Link to post Share on other sites
Sparky-(Admin) 21,318 #946 Posted August 14, 2021 5 1 Share this post Link to post Share on other sites
AMC RULES 37,130 #947 Posted August 14, 2021 3 hours ago, johnnymag3 said: C 120 getting ready for tear down, and refreshing........Not going to paint anything. Just going to clean it.... replace and give it NEW Hoses, Filters, Fluids, and any other mechanical thing thats looking too worn for duty... A nice seat is in its future also. Thanks for keeping it real bro! 👍👍 2 Share this post Link to post Share on other sites
johnnymag3 2,520 #948 Posted August 14, 2021 These tractors are only ORIGINAL once.....I will be trying to use all oem Wheel Horse clamps, bolts and visible fittings when I freshen it up.....and have to replace anything... Gotta keep em Original !!!! When at all possible !!!! 1 1 Share this post Link to post Share on other sites
AMC RULES 37,130 #949 Posted August 14, 2021 Shouldn't be too hard to accomplish with that one. 1 Share this post Link to post Share on other sites
johnnymag3 2,520 #950 Posted August 14, 2021 1 minute ago, AMC RULES said: Shouldn't be too hard to accomplish with that one. Gonna do my best !!!!! Thanks 1 Share this post Link to post Share on other sites
