ebinmaine 67,498 #2376 Posted September 10, 2023 2 hours ago, Sparky said: get the mud and crud off the two rigs that cruised the trails. You get that stick out of the tread you were going on and on and on and on and on and on about in the Meet n Greet thread? 1 Share this post Link to post Share on other sites
Sodaking27 777 #2377 Posted September 10, 2023 Little fall trimming going on today. 6 2 Share this post Link to post Share on other sites
ML3 1,203 #2378 Posted September 13, 2023 On 9/10/2023 at 10:09 AM, Sparky said: After a great meet/greet up at @JCM Jim’s in Maine yesterday it’s time to get the mud and crud off the two rigs that cruised the trails. My new Stihl electric pressure washer to the rescue Recently bought that same Stihl pressure washer. Works great & not too expensive. Only a few dollars more than most cheap discount store washers. 3 Share this post Link to post Share on other sites
Sparky-(Admin) 21,318 #2379 Posted September 16, 2023 3 8 Share this post Link to post Share on other sites
Sparky-(Admin) 21,318 #2380 Posted September 16, 2023 Mowed with the 414 today…. 9 3 Share this post Link to post Share on other sites
Sparky-(Admin) 21,318 #2381 Posted September 16, 2023 My next project…. 9 1 Share this post Link to post Share on other sites
ebinmaine 67,498 #2382 Posted September 16, 2023 8 minutes ago, Sparky said: My next project…. Oh?? Share this post Link to post Share on other sites
Sparky-(Admin) 21,318 #2383 Posted September 16, 2023 9 minutes ago, ebinmaine said: Oh?? Sure…but I’m not gonna give it a name and have an 80 page thread on it Just messing with ya! 7 Share this post Link to post Share on other sites
ebinmaine 67,498 #2384 Posted September 16, 2023 2 minutes ago, Sparky said: Sure…but I’m not gonna give it a name and have an 80 page thread on it Just messing with ya! Hey! HEY!! it's only 74 pages...... Today. 5 Share this post Link to post Share on other sites
19richie66 17,508 #2385 Posted September 16, 2023 (edited) No more projects with names for me. IF, and I say IF, I ever get something done, then I’ll post it. Till then, I’m done. Something always comes along that takes my time, money or my enthusiasm. That being said, here’s a side shot Edited September 16, 2023 by 19richie66 8 5 1 1 Share this post Link to post Share on other sites
Tonytoro416 1,034 #2386 Posted September 16, 2023 6 6 2 Share this post Link to post Share on other sites
AMC RULES 37,130 #2387 Posted September 16, 2023 6 4 Share this post Link to post Share on other sites
davem1111 2,030 #2388 Posted September 16, 2023 Back in the garage after several hours of trail mowing and weed whacking. GT-1848 with Honda GX610 twin. 2 9 Share this post Link to post Share on other sites
davem1111 2,030 #2389 Posted September 16, 2023 Oh, and a side shot of the 417-H, well "was" a 417-H and may be again, not sure. Missing some parts here, have an engine but don't know if it runs. 6 2 Share this post Link to post Share on other sites
Bill D 1,921 #2390 Posted September 16, 2023 10 minutes ago, davem1111 said: Oh, and a side shot of the 417-H, well "was" a 417-H and may be again, not sure. Missing some parts here, have an engine but don't know if it runs. I like it. Looks like a worth while project. 2 Share this post Link to post Share on other sites
davem1111 2,030 #2391 Posted September 16, 2023 1 hour ago, Bill D said: I like it. Looks like a worth while project. I agree, with a bit of hesitation. The PO passed away, and his son didn't know much about it. So I don't know if the trans is good, and the engine was either rebuilt already, or needed to be and wasn't yet. Wiring is either a mess or non-existent. So I guess I could drop the engine on it, do the minimal wiring needed, see if it runs well and the trans works. If all is well, I think it would be worthwhile. If not, I may just pass it along to someone else. I have 3 others that either need work or I'd rather spend the time fixing up nicely. We shall see. 3 Share this post Link to post Share on other sites
19richie66 17,508 #2392 Posted September 16, 2023 (edited) I won’t stop till I collect them all (I have nothing at the moment worthy of a side shot) Edited September 16, 2023 by 19richie66 5 3 1 Share this post Link to post Share on other sites
c-series don 8,707 #2394 Posted September 17, 2023 I took this photo around 5 years ago in my backyard 3 10 1 Share this post Link to post Share on other sites
johnnymag3 2,520 #2395 Posted September 17, 2023 2 13 Share this post Link to post Share on other sites
19richie66 17,508 #2396 Posted September 17, 2023 Shelf Sunday? 7 2 3 1 Share this post Link to post Share on other sites
Sparky-(Admin) 21,318 #2397 Posted September 17, 2023 Couple side shots of machine’s in my garage “going under the knife”… 308 and a 312 5 2 Share this post Link to post Share on other sites
AMC RULES 37,130 #2398 Posted September 17, 2023 854 top side. 2 7 2 Share this post Link to post Share on other sites
davem1111 2,030 #2399 Posted September 17, 2023 Out trying to tame the jungle today. 5 2 1 Share this post Link to post Share on other sites
