ebinmaine 68,514 #1 Posted March 15, 2020 (edited) I've been thinking of building a holder of some sort or modifying an existing bench for quite a while. Needed to work on the 8 speed for Colossus so I decided now was a good time. I put some thought into what and where would be the best location to pop a couple holes in an otherwise perfectly fine surface. There's a space between the toolboxes on my low rise bench that I don't use for anything but setting something for minute (or a month). Edited March 15, 2020 by ebinmaine 7 8 Share this post Link to post Share on other sites
953 nut 55,909 #2 Posted March 15, 2020 I have a small rolling table that has similar holes cut in it, my holes are no where near as tidy as yours though! 1 Share this post Link to post Share on other sites
Terry M-(Moderator) 2,176 #3 Posted March 15, 2020 I kinda like the idea...But I'd hate to put a hole in my workbench. 1 Share this post Link to post Share on other sites
ebinmaine 68,514 #4 Posted March 15, 2020 1 minute ago, Terry M said: I kinda like the idea...But I'd hate to put a hole in my workbench. I like @953 nut Richard's idea of a table. I think it was @WHX24 that also has one. I've been watching my habits for weeks to see where was the least inconvenient place. 2 1 Share this post Link to post Share on other sites
"Manic-Mechanic" 1,195 #5 Posted March 15, 2020 Excellent work! You must of cut in some receptacle boxes? Lol Share this post Link to post Share on other sites
ebinmaine 68,514 #6 Posted March 15, 2020 9 minutes ago, oldman said: Excellent work! You must of cut in some receptacle boxes? Lol Those are from a wall that was removed when we had the oil spill a little over a year ago. At some point I may possibly remember to attach them to the ceiling. Share this post Link to post Share on other sites
gwest_ca-(File Mod) 11,107 #7 Posted March 15, 2020 Screw a piece of flat sheet metal to the piece you cut out and instant plug when the hole is not needed. Garry 3 Share this post Link to post Share on other sites
Shynon 7,461 #8 Posted March 15, 2020 I have a metal milk crate I use cut out 2 holes in the bottom and cut open the front and put in my engine building stand. 5 Share this post Link to post Share on other sites
squonk 41,464 #9 Posted March 15, 2020 9 minutes ago, Shynon said: I have a metal milk crate I use cut out 2 holes in the bottom and cut open the front and put in my engine building stand. Um, the school district is still looking for that crate! 5 Share this post Link to post Share on other sites
ebinmaine 68,514 #10 Posted March 15, 2020 1 minute ago, squonk said: Um, the school district is still looking for that crate! Not right now.... They're all closed for 2 weeks to disinfect. 2 1 Share this post Link to post Share on other sites
SylvanLakeWH 25,999 #11 Posted March 15, 2020 39 minutes ago, squonk said: Um, the school district is still looking for that crate! Looks like a NOS WH factory accessory to me... 1 Share this post Link to post Share on other sites
ebinmaine 68,514 #12 Posted March 15, 2020 I put this setup to good use today. I'll update the Colossus'ussess' thread soon. Soo niiice to have a good steady third hand when putting the transmission together. Best part was when dropping the top half in place. NO movement from the bottom when trying to keep the shafts lined up and set the halves together. Share this post Link to post Share on other sites
