Jump to content
Sign in to follow this  
Followers 0
BMW1

D series transaxle axle bearing and seal installation question

By BMW1, in Transmissions and transaxles

Recommended Posts

BMW1    44

BMW1
Posted

I have not had to do this before and want to make sure I'm doing it correctly.

 

Picture of bearing and seal is attached.

 

Is the bearing supposed to fit in the groove of the oil seal or is the seal supposed to flush against the bearing?  I think the latter is correct?

 

Thanks

Dseries rear axle bearing and seal.jpg

Share this post

Link to post
Share on other sites
 

pfrederi    21,043

pfrederi
Posted

push the bearing in about 1/4" in from end of axle housing.  press seal in flush with end of axle housing.  Seal doesn't  touch bearing. If you push the seal up against the bearing you can deform the lip so it does not  seal nicely on the axle shaft

  • Like 2

Share this post

Link to post
Share on other sites
 

BMW1    44

BMW1
Posted

Thank You!!!

  • Like 1

Share this post

Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  
Followers 0
Go To Topic Listing

  • Similar Content

    • BuffaloD200
      Ark Loader Spool Valve
      By BuffaloD200
      Finally getting around to working on my ark loader.  The previous owner said he thinks the problem is with the spool valve.  
      As I've learned a bit more about hydraulics now, I'd like to get this all sorted out.  
      I noticed the power beyond port is connected to the reservoir return.  Is that right?  
      Anyone see anything blatantly incorrect?



    • ccs002
      D-160 Hydro Pump
      By ccs002
      Looking for a complete hydro pump for a D-160. Tractor is missing everything from the rubber coupler disc back. Also willing to buy a complete tractor for parts, the closer to Harrisonburg VA the better. Thank you. 
    • tractorboy79
      GT14/D series lift cylinder modification
      By tractorboy79
      I was looking around on ebay and noticed that hydraulic actuators from John Deere 312, 317, etc models appear to be Identical to a Gt14 or d series lift cylinder. My question is would a new cylinder from ebay be able to replace one that is on a gt14 or d series?
       
      Images below of cylinders to show similaritys.


    • BuffaloD200
      HELP! D-Series Clutch
      By BuffaloD200
      '74 D-180
       
      My friction disc in gone on my clutch.  I saw the old post about making a new friction disc, so I'm not concerned about that.
      I managed to remove the front clutch plate and double v-belt pulley.  But I can't separate the two.  When I took the assembly off the spiraloc washer popped off on its own.  I HAVE READ THE MANUALS.
      So I should be able to just remove the pulley from the front clutch and continue with step 4.  The v-belt pulley is loose as all hell and flops around like a dead fish.  It seems to be hung up on a ring or bearing race.  
      So my thoughts are grab a BFH or sparky the blue tip wrench.
      Is there an unpublished step 3.5, or some trick?
    • BuffaloD200
      D-Series One Wheel Peel
      By BuffaloD200
      Hey all, 
       
      My '74 D180 has a lot of trouble pushing snow.  Weighted tires, but nothing else at this time.  I've found it gets stuck frequently and only one wheel spins.  Do these tractors not have a limited slip/locker arrangement?  How does everyone manage with the infamous one wheel peel?
×
×
  • Create New...