Jump to content
Rob R

Kohler 321 Engine Pan

Recommended Posts

Rob R

 I am currently doing a ring, piston, hone rebuild on a K 321 off a Ford LGT 145 Tractor  on this machine they actually welded the rails to the bottom pan (see pics). My intention here is to put this puppy in a red machine (312-8 or GT14). I definitely have the small pan with the expanded bottom for the long dipper.

Here's my questions:

> Can I carefully remove the rails from the pan, cutoff the old front axle mounting bracket(s) and then drill holes in  the flanges to mount  to the Wheel Horse rails.

> Since the engine is side mounted will the expanded bottom fit between the standard Wheel Horse rails?

> If not possible to make this old pan work what flat pan would work and do I need to get the expanded bottom one (big dipper}

> any recommendations here would be appreciated don't want to go down to many blind holes here...….

 

Thanks much!

IMG_0252.JPG

IMG_0253.JPG

IMG_0254.JPG

IMG_0255.JPG

IMG_0256.JPG

IMG_0257.JPG

IMG_0258.JPG

IMG_0259.JPG

  • Like 1

Share this post


Link to post
Share on other sites
 
daveoman1966

What is the pan-to-engine bolt pattern?  How deep do you need the pan to be?  I have several pans here from 12-14 Kohler engines,but need to know a little more.  Canm we do this in emails...outside of RS?  My email is:

daveoman@windstream.net...

 

 

Share this post


Link to post
Share on other sites
 
WHX??

I would not use the Ford pan. It was for a tube frame and I think it would not be worth the effort to modify it.  It may have some value to the Ford collectors. Should be able to just put a standard K series deep pan on it. Those should be easy to find. The dipper clearance should be check and trimmed if required. I don't see the use of a short pan with the tractor you are putting it in. You probably have seen this Rob but just for reference here.

https://www.wheelhorseforum.com/topic/44945-identifying-big-block-kohler-block-styles/

Are you going to leave the balance gears in?

Edited by WHX22

Share this post


Link to post
Share on other sites
 
82Caddy

Easiest option would be a pan like this:

 

s-l1600.jpg

 

With that said, none of your belts, guards or the like would line up.  The pan is about an inch shorter then what a wheel horse pan is so the engine will sit closer to the frame.

Share this post


Link to post
Share on other sites
 
WHX??
30 minutes ago, WHX22 said:

Should be able to just put a standard K series deep pan on it.

After further review scratch that idea... won't fit that block. Caddy's got a good plan tho. Maybe space it up on channels for better fit with the guards? May have to notch the frame for clearance on the deep sump. Or go with the shallow pan without the sump,  snip the dipper and space it up? Just thinkin out loud here.  

Edited by WHX22

Share this post


Link to post
Share on other sites
 
Rob R
22 hours ago, WHX22 said:

I would not use the Ford pan. It was for a tube frame and I think it would not be worth the effort to modify it.  It may have some value to the Ford collectors. Should be able to just put a standard K series deep pan on it. Those should be easy to find. The dipper clearance should be check and trimmed if required. I don't see the use of a short pan with the tractor you are putting it in. You probably have seen this Rob but just for reference here.

https://www.wheelhorseforum.com/topic/44945-identifying-big-block-kohler-block-styles/

Are you going to leave the balance gears in?

Thanks for the response Jim what you are saying makes perfect sense I definitely need a small K series deep pan (at least 2 inches) and probably need to trim the dipper as I have the long one and the current Ford pan has a deeper valley on one side.....  The balance gears are good and very tight so I planned on leaving them in.... plus I don't know how to take them out...…  Anyone out there have one of these at a decent $? 

Edited by Rob R

Share this post


Link to post
Share on other sites
 
Eric Friedrichsen

Rob,

 

I have a spare Magnum 321 pan in good condition that you can have. I live in Wilton CT which is only 30 min. from Brewster.

If you want it call me at 203-752-0043. The depth of the pan from the base to the gasket edge is 2 and 3/8 inches. It should fit

your engine fine.

 

Eric Friedrichsen

016.JPG

017.JPG

018.JPG

019.JPG

  • Sad 1

Share this post


Link to post
Share on other sites
 
82Caddy

That’s the wrong kind of oil pan for a small base engine (more square). That will only work with a big base engine block (long rectangle). 

  • Like 1
  • Excellent 1

Share this post


Link to post
Share on other sites
 
Shynon
38 minutes ago, 82Caddy said:

That’s the wrong kind of oil pan for a small base engine (more square). That will only work with a big base engine block (long rectangle). 

:text-yeahthat:

Share this post


Link to post
Share on other sites
 
953 nut

Check out this post and see how Jay @JPWH tackled this issue. Start with Post # 78.

 

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • wh315-8
      By wh315-8
      I have a question about the 69’ model. I took my tank out to work on carb easier. A couple weeks later as I put it back together & after cleaning everything; I replaced the white weatherstripping that was at bottom of tank and on the corners of the strap. Seems to be all that holds it in place. Because the strap around the tank will not go around the metal bracket on bottom and fit the tank. And even if it did the strap would only line up with the bracket mounting bolts which would be in the way. What did I miss? Didn’t pay close enough attention when I took it apart and can’t see in the parts diagram where the strap does go around the bracket. The weather stripping is tacky enough that the tank stays in place and it is a made to fit perfectly in position. Just seems that the metal strap is pointless.




    • tractorboy79
      By tractorboy79
      I have a old gt14 and the plastic plates or control panels are way past their prime, and I saw someone was remarking them with a 3d printer a little while back and I was looking to se if I could find the file but no luck. If anybody has info that would be amazing. Thanks for your time and anything helps.
    • Don66
      By Don66
      I have a 1978 Wheel Horse 8 speed tractor,Kohler 321 engine. I've been working on restoration, finally got the mower deck finished and installed. Before this, the engine was easy to start and ran well. Yesterday it would not start with ignition key, would not even turn over, so I jumped it with a screwdriver between cylinoid and battery. The engine started and ran about 10 seconds and died. Now I get no spark and the engine won't fire off. I checked the wiring and everything seems to be connected and without damage. I don't have test equipment available so I'm stumped at what went wrong. Any suggestions?
    • 12 hp Kohler
      By 12 hp Kohler
      Saw a gt14 for a really good price on Craigslist yesterday went and looked at it last evening, ended up buying it . It’s a 68 or 69 gt14 but I’m not exactly sure which. It’s in decent condition and seems to be complete. It has a really nice complete three point hitch and a really nice three point tiller. I didn’t think the seat and muffler were original but I looked at a manual and it turns out they are. I’m gonna try to get it running for the big show but if I don’t I will still take it. The best part is I bought it from a super nice guy that knows a lot about wheel horses. Some of you might know him, his name is Less, sorry didn’t catch his last name. He has been going to the wheel horse show since the beginning and personally knew Cecil and Betty Pond. He used to have 74 tractors but he narrowed it down to his favorite three. Overall it was a really good day. I got to meet a really nice guy, get another tractor and hear some good stories. Here are a few pictures of the gt14 and tiller. I am gonna start working on it this Sunday. 
      Tractor or serial number 

        
      Tiller serial number 


    • swisstrac
      By swisstrac
      looking for info/help re securing a front wheel bearing/race for  GT14/ 1971;  any info would be much appreciated.. 
×
×
  • Create New...