Jump to content
Fish Crawford

310-8 trans fluid 80w90?

Recommended Posts

Fish Crawford

New wheelhorse owner 85 310-8...was told had issues freezing during winter and "supposedly" changed fluid last yr. Checkd distick and thick white almost like melted milkshake consistency. Is 80 w 90 gear oil whats suppose to be wat it calls for?  Need suggestions...

Share this post


Link to post
Share on other sites
 
WHX??

You got water in the transmission  no doubt. . Drain completely and refill with fresh 80/90. Then run it and do it again. Whoever told you it was "just changed" might be on crack.

Don't tell me lemme guess I bet this tractor sits outside? Please tell me I'm wrong. 

In case I haven't done so :WRS:

  • Like 2

Share this post


Link to post
Share on other sites
 
Fish Crawford
11 minutes ago, WHX22 said:

You got water in the transmission  no doubt. . Drain completely and refill with fresh 80/90. Then run it and do it again. Whoever told you it was "just changed" might be on crack.

Don't tell me lemme guess I bet this tractor sits outside? Please tell me I'm wrong. 

In case I haven't done so :WRS:

Yes sir u are right it has been stored outside...i will change it out as u said and then do it again. Thank u!

Share this post


Link to post
Share on other sites
 
Achto
1 minute ago, Fish Crawford said:

Yes sir u are right it has been stored outside...i will change it out as u said and then do it again

 

If the shifter boot is bad, water will find it's way into the tranny quite easily. If the boot is bad, i suggest changing it.

  • Like 3

Share this post


Link to post
Share on other sites
 
Fish Crawford

Shifter boot is torn as well..darn im glad i found this website! ☺👌

  • Like 3

Share this post


Link to post
Share on other sites
 
WHX??

:text-yeahthat:You may also want to drain, replace with diesel or kerosene, to clean it and flush. Replace with 80/90. May have to do that several times. 

Sorry Fish but we have see mistreated horses many times here before. Not your fault for how  a PO neglected a horse but your time to step up to the plate you want a working tractor. :)

  • Like 1
  • Excellent 1

Share this post


Link to post
Share on other sites
 
Fish Crawford

Thats wats so crazy it runs like a scalded dog right now. ..i can only imagine what it will be like after i get that crud outta there

  • Like 1

Share this post


Link to post
Share on other sites
 
953 nut

:WRS:

When you drain the milk shake out of the transmission be sure to jack up the front end of the tractor. There is a hump in the bottom of the case that will trap some of the old crud in there. Here is a good place to buy a new shift lever boot.

https://www.wheelhorsepartsandmore.com/transmissions.html#!/Wheel-horse-3577-shifter-boot/p/84932555

  • Like 5
  • Excellent 1

Share this post


Link to post
Share on other sites
 
The Tuul Crib

:text-welcomeconfetti:to:rs:

 

:wwp: definitely drain it and fill it up w/  Diesel fuel several times .and drive it around in between! 

  • Like 2

Share this post


Link to post
Share on other sites
 
peter lena

agree with the fed back above, that milk shake mix is defiantly   water , when you change out that shiftier boot , i use a razor blade to cut it off, then use grease on the shiftier rod  and boot hole to install , make it easy and smooth. another thing, do you have any open road area near you? diesel fuel flush , combined with minutes on road will really help flushing and heating up. just rolling it around the yard  barely touches it, i also use every gear and hi/lo range change in the flushing, the difference is worth it. that " outside  " storage is a killer, if you haven,t done it , try using some  WD 40  on a rag to wipe down your horse, it will feed the paint and transform the dull look of your unit.  good luck , Pete 

  • Like 2

Share this post


Link to post
Share on other sites
 
clueless
7 hours ago, 953 nut said:

:WRS:

When you drain the milk shake out of the transmission be sure to jack up the front end of the tractor. There is a hump in the bottom of the case that will trap some of the old crud in there. Here is a good place to buy a new shift lever boot.

https://www.wheelhorsepartsandmore.com/transmissions.html#!/Wheel-horse-3577-shifter-boot/p/84932555

Jack the front end up at least 18 to 20 inches every time you drain it.

  • Like 1
  • Thanks 1

Share this post


Link to post
Share on other sites
 
Fish Crawford

Thanks everybody...boot is ordered...headed to get some gear oil and diesel right now. Pics soon to come

  • Like 1
  • Thanks 1

Share this post


Link to post
Share on other sites
 
Fish Crawford

 Well slow progress is still progress.drained the " milkshake" and filled with diesel. Removed what was left of the boot..just waitn on new one to arrive and a few more rounds of drain- fill- flush n drive! 

0406191824.jpg

0406191824a.jpg

0406191842a.jpg

0406191913.jpg

0406191923.jpg

  • Like 2

Share this post


Link to post
Share on other sites
 
Warning:Unsupervised

Went through this with one I bought yrs ago. Tractor stored inside but po washed it after mowing (I use compressor btw). Leaf blowers work too.

Boot was shot on it, so milk shake city when I changed it too! 

 Very disturbing to see, like seeing bright color poo:scared-yipes:, uh oh, wth man?..lol

Even owners trying to care for a horse due more harm sometimes the good thing is they are built tough, hell mine still performs like new after 8 yrs hard use so don't sweat it's future use either. Worried me a bit afterwards but don't let it.

 

Share this post


Link to post
Share on other sites
 
peter lena

FISH  that 80-9- fluid will work , but i fully agree with others with a few flushings. i like atf fluid , and take it out for some road time ,in a near by cul de sac , lets me use every gear and heat things up on the road , as it gets cleaner you will notice an ease in shifter motion and use. road time is good to seafoam your carb and lines along with a fresh filter , i always bring a few tools along and correct other areas i find , full chassis greasing also goes along with this , 3 fittings on front axle , lift up front end to ensure grease gets to lower end of axle bend , " fan gear under dash on steering shaft " has the 4th fitting. this basic baseline lubrication will verify a needed service. i would also use an aerosol lubricant on any moving linkage or movement area, choke and throttle cables , pto lever set up, every bit of it should move easily , no be frozen in rust , let us know how you make out , pete 

Share this post


Link to post
Share on other sites
 
Fish Crawford

Well had to flush it about 4 times but i can really tell the difference. Much smoother shifting. Also had to repair roll pin on shifter collar as well . Fun little guys to work on ...until you need to buy parts lol. 

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...