Pullstart 62,837 #226 Posted November 5, 2018 Much better than a trash can! The Charger 12 axle is wider, and being a larger tractor I think this is the ticket... 4 Share this post Link to post Share on other sites
Pullstart 62,837 #227 Posted November 5, 2018 Building a battery box frame, the heavy plate will be the front. Once the frame is together it’ll get skinned with 1/16” plate and have a removable cover for battery access. 2 Share this post Link to post Share on other sites
Pullstart 62,837 #228 Posted November 5, 2018 I’m a little bit A.D.D. here I suppose. I cut the left foot rest and it looked funny. I realized the left was 2” wider than the right overall, in relation to the dash stand. Well, a little more cut and tack action took care of that. Thanks for following along on the build, but it’s time to go in for a few hours and grab a nap before tomorrow gets here! 3 Share this post Link to post Share on other sites
Pullstart 62,837 #229 Posted November 5, 2018 Pullstart’s shop is protected by Putt Putt, the junk yard dog. 1 5 Share this post Link to post Share on other sites
Pullstart 62,837 #230 Posted November 5, 2018 Not sure how much of this rear plow/tiller mount is factory , but it’ll make for a nifty fender mount! 1 1 Share this post Link to post Share on other sites
Pullstart 62,837 #231 Posted November 5, 2018 Battery box main frame is tacked up! 2 3 1 Share this post Link to post Share on other sites
LengerichKA88 1,883 #232 Posted November 5, 2018 Diggin the new additions! 1 Share this post Link to post Share on other sites
953 nut 55,194 #233 Posted November 5, 2018 7 hours ago, pullstart said: Not sure how much of this rear plow/tiller mount is factory , but it’ll make for a nifty fender mount! 1 1 Share this post Link to post Share on other sites
Pullstart 62,837 #234 Posted November 9, 2018 Tractors are wishing for some attention, but it’s clean up the shop night. And put the winter tires on momma’s ride night too. 3 1 1 Share this post Link to post Share on other sites
ebinmaine 67,434 #235 Posted November 15, 2018 On 11/5/2018 at 4:21 PM, pullstart said: Battery box main How's this held on the front of the tractor? I like the looks of it allot. Share this post Link to post Share on other sites
Pullstart 62,837 #236 Posted November 15, 2018 The 1x3 bar stock is drilled and tapped, bolted on from underneath. Everything is tack welded to that. It’s also got angle iron resting on the frame tacked to the bar stock too. 2 Share this post Link to post Share on other sites
Tractorhead 9,064 #237 Posted November 25, 2018 Kevin ? Helloooo, Ohh ohhh ohhhh. Hmm echoing ? Whats up to Mrs. Pullstart ? Hope youre well. still waiting to see the work, you're done. Share this post Link to post Share on other sites
Pullstart 62,837 #238 Posted November 25, 2018 1 hour ago, Tractorhead said: Kevin ? Helloooo, Ohh ohhh ohhhh. Hmm echoing ? Whats up to Mrs. Pullstart ? Hope youre well. still waiting to see the work, you're done. No news right now, we’ve been cleaning out our back storage barn, and getting campers and summer toys put away for winter. Along with that, I’ve been working on getting my snow equipment ready for winter (I plow commercially) and getting driveways, roads and parking lots marked out. And hunting! Share this post Link to post Share on other sites
Tractorhead 9,064 #239 Posted November 25, 2018 17 minutes ago, pullstart said: No news right now, we’ve been cleaning out our back storage barn, and getting campers and summer toys put away for winter. Along with that, I’ve been working on getting my snow equipment ready for winter (I plow commercially) and getting driveways, roads and parking lots marked out. And hunting! Hi Kevin, good to hear you are well. I have just wondered, but now i see, you are very busy. keep on Rockin and greeting to Family Stefan 1 Share this post Link to post Share on other sites
Pullstart 62,837 #240 Posted December 3, 2018 (edited) On 11/25/2018 at 9:25 AM, Tractorhead said: Hi Kevin, good to hear you are well. I have just wondered, but now i see, you are very busy. keep on Rockin and greeting to Family Stefan I scored some “me” time tonight, so I headed out to the shop. Doing some wiring layout and I shimmed the steering fan gear and snugged up the locking collar under the dash for good steering gear mesh. Edited December 3, 2018 by pullstart *snugged* Not *snuggled* 7 1 Share this post Link to post Share on other sites
Stormin 9,981 #241 Posted December 3, 2018 (edited) Oh 'Eck! Just read through this build thread and I'm begining to think it wasn't a good idea. Not your build I hasten to add. I think it's going to be the dogs whatsit's. I have a Raider 10 with a broken rod and knackered 3 speed trans'. A 14hp Kohler twin with vertical shaft. Six speed tran's off a Husqvarna which I've fitted WH hubs too. When I get the C-125 done, I think I'll have to see what I can come up with. Edited December 3, 2018 by Stormin 1 2 Share this post Link to post Share on other sites
Pullstart 62,837 #242 Posted December 3, 2018 1 minute ago, Stormin said: Oh 'Eck! Just read through this build thread and I'm begining to think it wasn't a good idea. Not your build I hasten to add. I think it's going to be the dogs whatsit's. I have a Raider 10 with a broken rod and knackered trans'. A 14hp Kohler twin with vertical shaft. Six speed tran's off a Husqvarna which I've fitted WH hubs too. When I get the C-125 done, I think I'll have to see what I can come up with. I’m sure it’ll be magical! Looking forward to the build Share this post Link to post Share on other sites
WHX?? 48,815 #243 Posted December 3, 2018 Whats the story with the show scoot in the first pic Kev? I noticed it when I was admiring your well kept work space! Share this post Link to post Share on other sites
Pullstart 62,837 #244 Posted December 3, 2018 41 minutes ago, WHX21 said: I was admiring your well kept work space! Organized khaos... it’s a ‘67 Puch. I posted it. As a non truck in the vintage trucks post. Fun to ride, 250 cc 2 stroke! 1 1 Share this post Link to post Share on other sites
Stormin 9,981 #245 Posted December 3, 2018 15 minutes ago, pullstart said: Alpine 150 Organized khaos... it’s a ‘67 Puch. I posted it. As a non truck in the vintage trucks post. Fun to ride, 250 cc 2 stroke! I've been try to identify those silencers. New they weren't British. My sister had an early '60 Puch Alpine 150cc scooter. 1 Share this post Link to post Share on other sites
Pullstart 62,837 #246 Posted December 4, 2018 I’d been having some electrical gremlins in the past with the C-101 that this harness (engine) came from, and I thought I had fixed it by cutting the safeties out of the circuit. That worked, or helped, until Frank’s maiden voyage test drive. I was halfway across the back 10 when it died out. I believe it quit giving the coil power when it was running. It fired up fine, but as soon as the starter position was released it would die. I decided to pull the switch apart and this is what I found. I’ll brake clean it, give it a polish on the contacts, fresh grease and try it out... 3 Share this post Link to post Share on other sites
Pullstart 62,837 #247 Posted December 4, 2018 A little brake clean, a little wire brush, a little grease... looks like it’ll work fine! I used channel locks to pull the switch housing apart, and the back side of the, to peen it closed. 2 1 Share this post Link to post Share on other sites
953 nut 55,194 #248 Posted December 4, 2018 33 minutes ago, pullstart said: A little brake clean, a little wire brush, a little grease... looks like it’ll work fine! Kevin, you are much more resourceful than most of us. Think I would have pulled a new switch off the shelf and tossed the old one. 1 Share this post Link to post Share on other sites
Pullstart 62,837 #249 Posted December 4, 2018 45 minutes ago, 953 nut said: Kevin, you are much more resourceful than most of us. Think I would have pulled a new switch off the shelf and tossed the old one. I was on the way to the parts store... then thought “why not look?” 2 1 1 Share this post Link to post Share on other sites
Pullstart 62,837 #250 Posted December 5, 2018 2 1 1 Share this post Link to post Share on other sites
