Jump to content
BB4029

Onan E125v head gasket

By BB4029, in Engines

Recommended Posts

BB4029    0

BB4029
Posted

Recently picked up an early 90's Wheel Horse 212-5 with Onan E125v. Intake valve was sticky and it had a bent pushrod. Can anyone tell me of a source for a new head gasket and a push rod? I've looked online but the only gasket I found was a used one on ebay. Thanks.

Share this post

Link to post
Share on other sites
 

gwest_ca-(File Mod)    11,090

gwest_ca
Posted

Welcome top the forum

Looks like you can get the head gasket from Toro but not the pushrod.

https://www.partstree.com/parts/toro/mowers-lawn-garden-tractor/32-12o501-212-5-toro-212-5-tractor-1990/cylinder-head-and-valves/

 

Let's hope Boomer sees this and can provide assistance on both parts.

If you need the service manual click on the picture first

Garry

Share this post

Link to post
Share on other sites
 

BB4029    0

BB4029
Posted (edited)

Thanks to the link you posted I've got the head gasket ordered. I've straightened the bent push rod but would really like to find a used or new one. I'll keep looking. Great forum with lots of valuable info. 

Just found a pair of used push rods on ebay. Thanks again for pointing me in the right direction.

Edited by BB4029

Share this post

Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Go To Topic Listing

  • Similar Content

    • lsc1257
      1996 Wheel Horse 520H With 48 Inch Deck
      By lsc1257
      I have a 1996 520H Wheel Horse for sale.  The tractor has just over 800 hours on it.  It comes with a 48 inch deck.  The deck is a 1995 and has over 1,500 hours on it, as it came brand new with my 312-8 that I sold several years ago.  This 520-H has the swept front axle so it can handle a 60 inch deck.  I just replaced the battery and the deck belt this summer.  The engine is a 20HP Onan and it starts right up but requires the full choke.  The transmission is an Eaton 1100-062, hydrostatic.  The deck is in rough shape but the spindles appear to be in good working order.  The right rear tire has some cracking.  The original operator's manual for the 520H is included, as is the original operating and maintenance instructions for the deck, plus the installation instructions for the deck.  Also included is a new PTO belt and several miscellaneous deck wheels and rollers.  Additional pictures available upon request.  Asking $500.



    • Joe Warren
      Service Tool Kit, Onan, ON-420-0556
      By Joe Warren
      Wheel Horse
      Service Tool Kit
      Onan Industrial Engines
      ON-420-0556
       
      Kit is missing oil filter tool, otherwise complete. Tools in excellent condition. Small crack in plastic case, bottom, middle. 
       
      $129 plus shipping cost.
       
      Message me if you are interested in purchasing. Thank you. Joe


    • SPINJIM
      520-H Restored w. deck, snow plow, & weights. SOLD
      By SPINJIM
      1992, Wheel Horse 520-H.   Onan overhauled: New rings, cylinders honed, valves lapped, new carb., new seals and filters, new fuel lines and primer bulb for easy starts.  Seat is like new.  Front tires are new.  All tires hold air.  Some repainting, but didn't need much; was stored indoors.  New decals.  Other new parts.
      Has swept front axle and Variable Ratio Steering.  Belt cover ventilated to cool back cylinder.  Rear wheel weights are 55 lbs. each.  
       




    • odee61
      416 8 Onan / 312 Hydro with a 12 HP Kohler
      By odee61
      Will the PTO work from the 312 Hydro with a 12 hp Kohler onto the 416-8 Onan?  My PTO disc went today. Any help would be most appreciated.
    • DVail2000
      Onan Engine Swap P2-16 to ???
      By DVail2000
      Ok, So I am seeing that most of you are leaning towards the ONAN engines being crap.  That said, I have 2 416's  # 1 is a -8 and # 2 is a -H.  Both have the -216 in them.  i was thinking of rebuilding the engine from the 416-H, but I am also considering changing the engine out with a different type.  What are the recomendations? I am seeing Koler, what else will fit?
       
       
      Thanks
       
      Dave.
×
×
  • Create New...