Torque spec ten pinion?

[mikeeyre74 289]

Does anyone know offhand the torque spec for the 10 Pinion limited slip differential bolts? 

[Racinbob 11,234]

20 ft. lbs.

[mikeeyre74 289]

That’s it? Weak!

[stevasaurus 22,872]

you want to use the nylon nuts.   That's why it is not a lot.  Actually, I think 20 ft lbs is what the torque is for lug nuts on your car tires. 

[953 nut 55,839]

7 minutes ago, stevasaurus said:

you want to use the nylon nuts.

8 minutes ago, stevasaurus said:

I think 20 ft lbs is what the torque is for lug nuts on your car tires.

You may want to rethink that one big guy!                            

CONTOUR - SVT	ALL / SVT	1998 - 1998	85 ft-lbs
	CONTOUR	ALL / P185/70R14	1998 - 2000	95 ft-lbs
	CROWN VIC	2/4 DOOR / P205/75R15	1987 - 2011	100 ft-lbs
	E-150	15"OPT. / STEEL WHL.	1992 - 2006	100 ft-lbs
	E-150	VAN / ALL	2007 - 2014	140 ft-lbs

[elcamino/wheelhorse 9,354]

53 minutes ago, stevasaurus said:

you want to use the nylon nuts.   That's why it is not a lot.  Actually, I think 20 ft lbs is what the torque is for lug nuts on your car tires. 

@stevasaurus That is the torque specs for the bolts that hold the Squonk 's head on his neck.

[WHX?? 49,177]

14 minutes ago, elcamino/wheelhorse said:

torque specs for the bolts that hold the Squonk 's head on his neck

 

[WHX?? 49,177]

1 hour ago, mikeeyre74 said:

That’s it? Weak

Some of the side plates  are aluminum and over torque WILL crack them.

[stevasaurus 22,872]

I stand corrected gentlemen.  Sorry for giving wrong information.    Not sure what I was thinking.

[squonk 41,367]

On 5/31/2018 at 5:39 PM, elcamino/wheelhorse said:

@stevasaurus That is the torque specs for the bolts that hold the Squonk 's head on his neck.

What? You think I wouldn't see this didn't ya. You old guys need to find something to do during the day. Here's something to keep you busy: What is the proper tool to tighten them. Torx? Allen Wrench? Hex ? ECT ECT. See if you can figure it out! 

[953 nut 55,839]

42 minutes ago, squonk said:

What? You think I wouldn't see this didn't ya. You old guys need to find something to do during the day. Here's something to keep you busy: What is the proper tool to tighten them. Torx? Allen Wrench? Hex ? ECT ECT. See if you can figure it out! 

                  Any questions?    

[squonk 41,367]

I don't see the proper tool or tools! Please try again! 

[squonk 41,367]

I'll give the answer after 3 tomorrow 

[DennisThornton 4,769]

Good lord!  You guys! 

🤣

[stevasaurus 22,872]

If it is the bolt between the head and the neck...it is a head bolt and requires the biggest torque wrench in the tool box.  The one with foot pounds. 

[squonk 41,367]

47 minutes ago, stevasaurus said:

If it is the bolt between the head and the neck...it is a head bolt and requires the biggest torque wrench in the tool box.  The one with foot pounds. 

Close 

[elcamino/wheelhorse 9,354]

@stevasaurus Don't over torque the nuts , may bust the aluminum side plates that holds Skonky's ears. 

[squonk 41,367]

Ok the Big Reveal! Ol' Case de ElCamino is going to have to find his tool box to see if he has the "Proper Tool(s) to torque my "head bolts" And here they are: You will need the tamper proof bit on the left and this left handed Metric torque wrench! No substitutes allowed as they will void all warranties! 

 

[stevasaurus 22,872]

Well...isn't that special.