What have you done to your Wheel Horse today?

[ebinmaine 67,485]

8 hours ago, rjg854 said:

Sweet looking tractor you got there 

@kto434... What he said.

[Danedg 20]

Today I was wondering about how to widen the rear wheel base to alleviate her nervousness about tippynes. 

Are there spacers or dually kits?

[pfrederi 17,739]

3 minutes ago, Danedg said:

Today I was wondering about how to widen the rear wheel base to alleviate her nervousness about tippynes. 

Are there spacers or dually kits?

What model are talking about.  It would take a steep hill to roll a WH sideways and it would be pretty obvious you shouldn't be there. also the engines have designed limits for tilting (oil starvation) that are less than potential roll over.

[johnnymag3 2,520]

He  has my B-80- I never felt tippy with it, maybe Dan should not mow side hills with a 45 degree angle      LOL

[Danedg 20]

13 hours ago, johnnymag3 said:

He  has my B-80- I never felt tippy with it, maybe Dan should not mow side hills with a 45 degree angle      LOL

 

Edited July 29, 2018 by Danedg

[pfrederi 17,739]

You could go to wider rear tires  23 10.50 12  (I assume you have 8.50s  on there now).  Going to duals would be expensive and put a lot of stress on the 1" axles i believe you have. And make mowing around things awkward as the tires stick out way beyond the deck  Dual adapters show up on ebay from time to time.

 

If you have a 36" deck you could do up to a 42" With the deck sticking out beyond the wheels roll over would be difficult to achieve.

[wallfish 16,999]

18 hours ago, Danedg said:

Are there spacers or dually kits?

This type doesn't allow dirt and mud to get between the rims. or at least not as much. Work very well and are easy on, easy off.  No or very little air pressure in the outside tires!

Mowing up and down the hill instead of sideways is better if possible.

https://www.ebay.com/itm/Dual-Wheel-Kit-for-Lawn-Garden-Tractor-Tires-John-Deere-Cub-Cadet-Wheelhorse/350099069962?hash=item518387dc0a:g:VhAAAOSwEehbMOxr

[oneroadkingman 53]

Well today put a fuel filter on my 520 new gas line Iran pull the gas tank out cleaned it put it back together changing the hydraulic oil put on axle seals in it

[rjg854 11,361]

 been trying since last week end to get the brake drum off so I can change the oil seal 

The hub came off without any issues. I've tried pb blaster, heat, wax, oil, carb cleaner.  BFHs, crowbars, pullers, impact wrench and even a grinder to be sure the end of the shaft hasn't mushroomed.   I  haven't given up yet, but, it may come down to cutting the  thing off.

 

I've moved it in and out on the shaft from the snap clip to the end of the shaft a couple of times but it just won't go any further than that 

Edited August 2, 2018 by rjg854
More

[oneroadkingman 53]

Well I didn't realize that putting hydraulic oil and was such a hard task it kept wanting to burp at me!

[Russell Aretz 16]

Today I went out to my shed and looked at my old tractor. And joined. She is a 1277 Runs and has all the goods.

[wallfish 16,999]

12 minutes ago, Russell Aretz said:

Today I went out to my shed and looked at my old tractor. And joined. She is a 1277 Runs and has all the goods.

That's funny Russell

Glad you're here.

 

Please don't run her without the engine blower cover! It will over heat

[AMC RULES 37,130]

Mowed the back yard...

with the new REO skiff this afternoon. 

Not a bad cut, considering it rained all night, and today until noon.

Then snatched up the high rise tub cart, just because it was there.   

 

 

 

[Russell Aretz 16]

I started to paint. I had er since1995. Done er over. Now its time to do it right. Please give me advise like give up or start over. 

[TonyToro 1,049]

Me and my little driver are fixing the Raider 12 that broke at the tractor pull. Broken woodruff key and buggered hub. 😞

The hub also cracked after trying to pull it off. I'll search the classifieds after this post for a hub. 

Edited August 5, 2018 by TonyToro

[Lane Ranger 10,968]

41 minutes ago, TonyToro said:

Me and my little driver are fixing the Raider 12 that broke at the tractor pull. Broken woodruff key and buggered hub. 😞

The hub also cracked after trying to pull it off. I'll search the classifieds after this post for a hub. 

 

 

I have done that too!     I did JB Weld the hub and It has held up for two years!   But I was not tractor pulling!

 

 

Edited August 5, 2018 by Lane Ranger

[rjg854 11,361]

Well at least you still have all the lug holes. Unless the key way is messed up, you'll have a backup,  or a hub to make a puller out of it.

[19richie66 17,505]

Welded the 1054 “tower assembly” to the gt14 frame. Now the fun begins. 

[Russell Aretz 16]

I started to paint. I had er since1995. Done er over. Now its time to do it right. Please give me advise like give up or start over. 

[thecoverworks 23]

Took it to a classic tractor show and steam fair !

Spoiler

 

 

[Tach-a-matic 357]

Mounted the blower and installed a new chain.  

 

[19richie66 17,505]

Clean machine there. 

[rjg854 11,361]

Looks like it ought to do the job.  But at 90+ degrees here today, I don't think you're going to get much seat time with it

[dells68 7,498]

I finally got the 8" front wheels on the 312.  Maybe over the winter I can find tine to paint the 42" deck.  Mowed with it tonight and it mows great.  I still need to add a little toe in on the front since switching out the front.  Here are a couple of before and after pics with the new wheels and deck.

[Dadlife520H 195]

11 hours ago, dells68 said:

I finally got the 8" front wheels on the 312.  Maybe over the winter I can find tine to paint the 42" deck.  Mowed with it tonight and it mows great.  I still need to add a little toe in on the front since switching out the front.  Here are a couple of before and after pics with the new wheels and deck.

 

 

The 8" look so much better. Been wanting to do the same to both of mine....