TonyToro 1,058 #501 Posted April 21, 2018 Got the pulling hitch all welded up. Crunch time now. Only 2 weeks until the first pull. 7 1 Share this post Link to post Share on other sites
elcamino/wheelhorse 9,326 #502 Posted April 21, 2018 Spend about 5 hours today change oil greasing all 3 horses. Sharpen blades on 36 in RD deck and pressure washed it so I can work on rust spots tomorrow . Have to lube both decks and sharpen blades on 42 inch rd tomorrow. Hope to have picture of me with herd tomorrow for supporter cards. 4 3 Share this post Link to post Share on other sites
squonk 41,158 #503 Posted April 21, 2018 26 minutes ago, elcamino/wheelhorse said: Spend about 5 hours today greasing .Hope to have picture of me with herd tomorrow for supporter cards. 3 Share this post Link to post Share on other sites
elcamino/wheelhorse 9,326 #504 Posted April 21, 2018 10 minutes ago, squonk said: We are going to have a game of greased Pig chasing at the BS . Guess who I nominate for the role of the pig ? 1 2 1 Share this post Link to post Share on other sites
squonk 41,158 #505 Posted April 21, 2018 1 hour ago, elcamino/wheelhorse said: We are going to have a game of greased Pig chasing at the BS . Guess who I nominate for the role of the pig ? 1 Share this post Link to post Share on other sites
WHX?? 48,833 #506 Posted April 21, 2018 on the polished tank @Shynon 2 1 Share this post Link to post Share on other sites
19richie66 17,508 #507 Posted April 21, 2018 21 minutes ago, WHX17 said: on the polished tank @Shynon Very nice! 1 1 Share this post Link to post Share on other sites
CountryRock 199 #508 Posted April 22, 2018 Started working on cylinder 1 head for my 246. Cut myself good on my left hand with a gasket scraper for a little scare. Got the valves lapped in the head, set the exhaust guide back to the correct height in the head. Had to order a couple more valve seals, valve keepers and head bolt washers. Why the valve gasket kit only comes with 2 valve seals and no head bolt seal washers is beyond me. Kinda enjoying working on this thing though. 2 Share this post Link to post Share on other sites
ebinmaine 67,658 #509 Posted April 22, 2018 10 hours ago, CountryRock said: Kinda enjoying working on this thing though That, my friend is the best part. 1 Share this post Link to post Share on other sites
cschannuth 3,816 #510 Posted April 22, 2018 I had some scraps left over from my FEL build and I needed some front weight for my 314-8 for when I have the sprayer on the back. I already had a small receiver hitch for the front so I built a smaller version of the weight rack that I made for the 520. I just need to clean it up and spray a little paint on it. With the two 42 pound weights and the bracket it weighs between 85 and 90 pounds. 4 4 1 Share this post Link to post Share on other sites
Lane Ranger 10,968 #511 Posted April 22, 2018 Saturday April 21, 2018 I put my Wheel Horse mid grader blade on my 603 to take to shows this year! Looks pretty cool if you ask me! Also painted up the tins on an 8 HP Kohler recoil start motor ! 3 10 Share this post Link to post Share on other sites
Goldann520 241 #512 Posted April 22, 2018 @jwalk2cc, @WVHillbilly520H, @elcamino/wheelhorse, @wheelhorseman, @953 nut. First of all sorry Johnny if I'd known you wanted it I'll always lean toward a red square member. It was savable for sure but pics made it look better than it was. Now the 312 done except for a new saddle and shoes. (See, I'm gettin this). Call or message any time johnny. You and, @Horse Newbie in Monroe only guys I got down here. I find stuff all the time and will keep you in mind. 5 Share this post Link to post Share on other sites
WVHillbilly520H 10,373 #513 Posted April 22, 2018 2 hours ago, cschannuth said: I had some scraps left over from my FEL build and I needed some front weight for my 314-8 for when I have the sprayer on the back. I already had a small receiver hitch for the front so I built a smaller version of the weight rack that I made for the 520. I just need to clean it up and spray a little paint on it. With the two 42 pound weights and the bracket it weighs between 85 and 90 pounds. Craig, well done there that'll keep them weights up out off the ground, Jeff. 1 1 Share this post Link to post Share on other sites
jwalk2cc 7 #514 Posted April 22, 2018 2 hours ago, Goldann520 said: @jwalk2cc, @WVHillbilly520H, @elcamino/wheelhorse, @wheelhorseman, @953 nut. First of all sorry Johnny if I'd known you wanted it I'll always lean toward a red square member. It was savable for sure but pics made it look better than it was. Now the 312 done except for a new saddle and shoes. (See, I'm gettin this). Call or message any time johnny. You and, @Horse Newbie in Monroe only guys I got down here. I find stuff all the time and will keep you in mind. No problem at all. And Thanks for the consideration, Just glad to know of another Red Square member close by. I really need to get the 3 other non running Wheel Horses finished before I buy anymore, but if a nice 414 -8 came along or C Series I would take a look. Johnny Walker Ha Share this post Link to post Share on other sites
cafoose 3,355 #515 Posted April 23, 2018 Put a new ignition switch on the 876 (I converted it to a relay system a few years ago after having problems with the original switch). Removed the snow thrower from the 520-HC and put the deck on. My neighbor welded a section from a scrap deck on the left side where it was rusted out. I think it turned out good! 3 Share this post Link to post Share on other sites
19richie66 17,508 #516 Posted April 23, 2018 Nice roadster in the background. Need more pics of that too👍 4 Share this post Link to post Share on other sites
cafoose 3,355 #517 Posted April 23, 2018 5 minutes ago, 19richie66 said: Nice roadster in the background. Need more pics of that too👍 That's my neighbor's roadster it's a '29 Model A with a 350 Chevy in it. When he gets it out I will try and get some 2 5 Share this post Link to post Share on other sites
19richie66 17,508 #518 Posted April 23, 2018 Cool. Love those old street rods. 👍 1 Share this post Link to post Share on other sites
TonyToro 1,058 #519 Posted April 24, 2018 More progress on the Work Horse pulling tractor. I got the wheelie bars mocked up and ready to weld and paint tomorrow. Hopefully by the end of the week I can get the body work painted. 3 Share this post Link to post Share on other sites
dells68 7,498 #520 Posted April 24, 2018 (edited) Got my lights wired on my 701. Bracket is some of my handiwork, but the lights and switch are genuine😀. Just noticed the eerie set of ghost eyes in the dark photo. Ghost of horses past?💀 Edited April 24, 2018 by dells68 5 4 1 Share this post Link to post Share on other sites
joskuk 67 #521 Posted April 24, 2018 Got the Vredestein V61 tires on the front of the 416. Easier to steer and no more air leaks! Pretty satisfied with the tires so far... 10 Share this post Link to post Share on other sites
Racinbob 11,096 #522 Posted April 24, 2018 This is how the 500 Special sat just over a year ago while still in Florida. It still sits just like that but now it's in our Indiana garage. I just didn't have the time to work on it. But today I took advantage of a fairly decent day. The belt guard is done, All the seat components are done. The fender is ready for final sanding and red paint. I'm using the seat mounting setup like the mid 70's B/C-series had with the flip forward mount but this one won't flip because the fender flips back. Now to find a sickle mower for it. 3 8 1 Share this post Link to post Share on other sites
19richie66 17,508 #523 Posted April 24, 2018 Looking great there Bob! 1 Share this post Link to post Share on other sites
Racinbob 11,096 #524 Posted April 24, 2018 Thanks Richie. It's sooooo close and I'm anxious to get it done and see how she runs. I've hated to neglect it for the past year but you certainly know how priorities go. I've got to disassemble the recoil and see what I screwed up when I put it together. It wobbles if I try to pull the rope. It wasn't like that before I did my handy work on it. 1 2 Share this post Link to post Share on other sites
Chris G 3,296 #525 Posted April 24, 2018 I got my radio on my custom 702 20180424_161745.3gp 6 Share this post Link to post Share on other sites
