What have you done to your Wheel Horse today?

[BrianKoch 307]

Installed hitch receiver from wheel horse parts & more 

 

Installed adjustable hitch 

 

Pulled the 4x8 utility trailer around cleaning up storm damage 

[The Freightliner Guy 1,327]

today i took one of the wheels off reese the rj so i can take it home and find a replacement

[oliver2-44 9,743]

7 hours ago, The Freightliner Guy said:

today i took one of the wheels off reese the rj so i can take it home and find a replacement

Are you looking for a tire or the actual metal rim?  Front or rear?

[The Freightliner Guy 1,327]

9 hours ago, oliver2-44 said:

Are you looking for a tire or the actual metal rim?  Front or rear?

front tires looking for both rims and tires

[Lane Ranger 10,968]

Putting the RJ back together that I had a very tight turning transmission on.  I took this to Florida in February and worked on it .  Started assembling last year.  I finally gave up on the two RJ ⚧️s I had for this rebuild and contacted Keith Jones in Ohio.  I madd a wild deal with Keith to give him several boxes of RJ and Suburban transmission parts and a couple full transmissions for a replacement rebuild in trade.   Keith also had His friend Larry “Ratpack” Eads assist him and analyze the problem.  Larry suggested two new axle’s which he machined as the old ones were pretty worn.

 

I had given Keith all new bearings, seals, brass bushings,  gaskets and side plate gaskets for the rebuild.  This transmission is an early 8 tooth brake gear not the later 11 . Keith and Larry worked on this thing over five Sundays getting all the old parts out, the new parts in and finding out what was causing the tightness in the axles Turing the gears.  It turned out that one of the axle tubes on the inside of one of the side plates was slightly bent and needed to be straightened! 
 

I picked it up on Sunday April 3pth which was the date Keith and I set for pick up back in March. 
 

I can’t thank these two guys rnough as this transmission is the smoothest turning thing!    Waiting for my wheel paint to dry before putting in my rear routes but racing to go ride this RJ.   I built this for my brother David. 

 

Edited May 3, 2023 by Lane Ranger

[kpinnc 12,017]

I got a little tinkering done today. I swapped front sneakers (16x7.50-8) out on the 314-8, and finally added the front wheel weights. The Vanguard is awesome, but very light weight compared to a Magnum. Given the lift on the back, every extra pound of ballast counts. 

 

 

[ebinmaine 67,460]

7 hours ago, kpinnc said:

every extra pound of ballast counts

You hang a Mackissic chipper off the front of that and your ballast concerns are forever solved.  

 

[Pullstart 62,843]

My little buddy chose Chloe first for our rides, but the field is still too wet to turn a furrow for the food plots.  It needs a new H10C plug as well, fouling up and loosing power with a load.  We parked the 953 and grabbed the WHRat for some golf ball pickin’. She got quite a bit of drive time logged!

 

*Any time she was by herself, the tractor was in low/1st.  Crawl speed indeed.

[kpinnc 12,017]

4 hours ago, ebinmaine said:

You hang a Mackissic chipper off the front of that and your ballast concerns are forever solved.  

 

I'd put it up there if I had one! 

[ohiofarmer 3,265]

Back in post 18898, I spoke of fixing the flat tires. Here they are, with tubes inserted and the things uninflated so that it would be easy to paint behind the outside bead. 

   Used the Rust-Oleum red primer and let it dry and then painted the inside of the tim with Almond Gloss.

   Then we mounted it to the tractor and spun on a finish coat and carefully coated the tim edge while keeping the tire back from the rim . The tire will be inflated later..While not as perfect as spraying the paint on, it worked very well using the rotating tire and holding the brush against it.

[Ed Kennell 38,162]

Loaded for the Steam-O-Rama Spring Fling.     I'll be there Fri. and Sat.

[ebinmaine 67,460]

1 hour ago, Ed Kennell said:

Loaded for the

Excellent. 

If all goes right we will be loaded up and strapped down before bed. Headed out in the morning.

[Handy Don 12,216]

1 hour ago, Ed Kennell said:

Loaded for the Steam-O-Rama Spring Fling

 

47 minutes ago, ebinmaine said:

we will be loaded up and strapped down before bed. Headed out in the morning

Safe travels to you both and I hope you have a great time!

[squonk 41,081]

Pressed in bearings in a 5025 Trans. Waiting for 1 more input shaft bearing. Used press on the capped ones and custom arbors and 7/16"  fine thread rod for the axle bearings and non capped ones. They have a lip to set the depth for the seals.

 

 

 

[ebinmaine 67,460]

1 hour ago, Handy Don said:

 

Safe travels to you both and I hope you have a great time!

You as well !! 

[BrianKoch 307]

Chores!

 

 

[ebinmaine 67,460]

Added decals to the seat of the newly restored '75 C160 Automatic.  

 

 

 

@Pullstart @c-series don

 

 

 

I'd put more there if I had 'em.  

 

[Pullstart 62,843]

Sweeeeeeeeeeeeet!

[c-series don 8,690]

@ebinmaine Wow Eric! That’s awesome, I’m honored! Thank you 🙏👍🏻

[ebinmaine 67,460]

41 minutes ago, c-series don said:

@ebinmaine Wow Eric! That’s awesome, I’m honored! Thank you 🙏👍🏻

That'll be on display at Zagray this weekend. 

 

[Pullstart 62,843]

I’m going to try to link this video here… fun with my niece and I’m not in jail for endangerment yet!

 

https://www.tiktok.com/t/ZTRwgQxEf/

 

 

[squonk 41,081]

Just watin on an axle.

 

 

[bswet1 39]

New front tires and some deck work on my 312-8. Hoping to mow with it for the first time this weekend. 

[pfrederi 17,734]

Used the 310-8 (with 10 pinion LSD) to haul my new roller ..finally one that has some real weight...+/- 400 lbs  WH is my "Mudder" tractor  fat tires LSD no weight no ruts

 

 

[bswet1 39]

And said first mow with my new to me 312.... Sounds like a B52 bomber but cuts really well! A little fine tuning to do but super happy.