What have you done to your Wheel Horse today?

[whtractors24 3,116]

She’s getting fluids changed . 

[squonk 41,096]

On 1/16/2023 at 9:13 AM, Ed Kennell said:

My local auctioneer sells a couple pieces every week..    He lists them as clothes dryers.

Those treadmills run up the electric bill but treadmill racing is a blast! 

 

 

[wallfish 16,995]

5 minutes ago, squonk said:

treadmill racing is a blast! 

That was a blast. !!!!!!!!!!!!!!!!!!!!!!!!!!!!!

I gotta go out and get some cars now to race on the wife's coat rack

[8ntruck 6,999]

Cool.  I can hear the serious collectors of these things cringing as you put them to some appropriate scale use.

 

Those cars part of the series that Lionel has been selling for a few years?

[GAJoe 844]

I got my other tire mounted on Friday and went to put it back on but noticed a bad wheel bearing. I did a search and found the XiKe bearings that several use from Amazon and got a four pack on order. Yesterday when I checked the tracking they were due to arrive today on Sunday so I got prepared to remove and replace the seals to do a grease swap-out with Lucas Red that I had in a gun. (Saving the green for mower deck spindles and mule bearings.) This was my first time removing the seals and cleaning the cheap grease out. It wasn't difficult just time consuming; but should pay off in the long run. 

 

Everything was going well on schedule until I went to put the new bearings in. The outboard went in about half way with just a tap or two to have it set in the hub but the inboard was loose in the hub. I don't know if the original was large of if I didn't progress in small enough increments when I knocked it out. Regardless I needed to find a way to reduce the hub diameter so that the outer race would snug up and stop spinning freely. I could see the hub around the shoulder of the bearing on this side by a few thousandths. I measured and it was around 1.508" outer diameter. I needed a swaging tool that would squeeze it to something close to 1.500". Then I remembered that the main rear axle shaft roller bearing was about what I needed. I located my old bad bearing and found that one inside diameter was champhered at a 45 and the other was rounded nicely. But how would I maintain the axle bearing centered around the shoulder of the new bearing to swage the hub evenly and not make a mess of it. I cut up an aluminum soft drink can into a few 1/4" strips that fit nicely inside the axle bearing inside diameter and around the new wheel bearing shoulder. It took three layers to get rid of the slop and hold things in place. I rested the opposite bearing outer shoulder on my big aluminum cylinder (Resting on plywood on the basement floor not the can of grease.) so that the inner race wouldn't take any of the force to swage the hub.

I laid a heavy plate of steel on the old axle bearing and smacked it sharply with a two pound hammer. When I lifted the plate to my delight the axle bearing was driven down onto the wheel hub. I got the axle bearing removed and the wheel bearing still had a little play in it so I repeated the process but now didn't need the shimming to keep the axle bearing centered. This time the wheel hub was swaged firmly around the wheel bearing.

 

The old axle bearing will go into my growing collection of special improvised WH tools.

Edited January 22, 2023 by GAJoe

[ebinmaine 67,462]

42 minutes ago, GAJoe said:

The old axle bearing will go into my growing collection of special improvised WH tools.

Those will be handy when you buy more Horses! 

😃

[squonk 41,096]

5 hours ago, 8ntruck said:

Cool.  I can hear the serious collectors of these things cringing as you put them to some appropriate scale use.

 

Those cars part of the series that Lionel has been selling for a few years?

In that video those are matchbox size. I have seen the bigger cars on some videos.

[Pullstart 62,846]

Moving some stuff around for a visitor today…

 

 

[19richie66 17,500]

39 minutes ago, Pullstart said:

Moving some stuff around for a visitor today…

 

 

 

Assisted living for Seniors? 

[Chestnut 315]

Winter has finally arrived in this part of Maine. We had a few storms earlier but I wasn't able to get the WH out to blow snow. I thought I was ready when I moved it into winter shed, but when I went to start it in December I got a handful of gas from the two year old Chinese primer bulb.Then the nipple snapped off the plastic fuel pump (same origin, same vintage). Maybe someday I'll learn. Anyway, the new Facet electric pump was ready to go for the most recent couple of storms. Wiring is still kind of temporary. I wired the pump through a rocker switch the PO installed for headlights. I want to wire through the key/ignition switch but hesitated to hack into the already sketchy wiring. Facet suggested wiring through the oil pressure switch. I was thinking of wiring it through the unused terminal on the 520-H key switch. The wiring diagram shows it should be life in the "run" position. Any suggestions?

Also got out for several walks. About time for snowshoes, but my friend is impatient as I fumble with the camera.

 

[Lee1977 6,658]

I wired my 520 through the unused R Terminal on the key switch for the hot wire.  The ground wire to a toggle switch then to ground. I can used the toggle to run the carb. dry.

[8ntruck 6,999]

@Pullstart- when did you get the snow?  I made a quick trip up last week, coming back south on Friday.  No snow on the ground when I left, just flurries along  I-196.

[Pullstart 62,846]

7 hours ago, 8ntruck said:

@Pullstart- when did you get the snow?  I made a quick trip up last week, coming back south on Friday.  No snow on the ground when I left, just flurries along  I-196.

The last two nights, we’ve gotten a blanket.  It’s supposed to be 35 today and the ground isn’t frozen so it likely won’t last another day.

 

I had a visit from @Blasterdad yesterday.  He brought me some parts for a project I’m working on, and I promised him a ride on Mrs. P’s Senior.

 

 

[Chestnut 315]

21 hours ago, Lee1977 said:

The ground wire to a toggle switch then to ground. I can used the toggle to run the carb. dry.

Thanks.  I like the idea of the toggle on the ground to let the bowl run dry.

[KrazeyOlDave 860]

Oops

[pfrederi 17,736]

4 minutes ago, KrazeyOlDave said:

Oops

 

 

That tire looks a bit narrow for that wheel.

[Blasterdad 2,692]

2 hours ago, KrazeyOlDave said:

Oops

That loader is way too heavy for that tire, you can just sell the loader to me, easy fix!  

Edited January 26, 2023 by Blasterdad

[GAJoe 844]

I hope that I have found all the worn out parts.

 

I first told my friend that "they make these things to last forever". But I revised that to "They make these things to be able to repair forever." That's better than what you buy today that are designed to wear out so that you have to buy a new one.

I made some new tie rods with grade 7B all-thread in stainless tubing that I had horded.   @peter lena Should I put Lucas Red in those ball joints as best I can?

 

Here's the access to the ball. I'm not sure how much grease can get into it.

Edited January 27, 2023 by GAJoe
added details.

[peter lena 8,620]

@GAJoe been using heim joints for years , no failures , like super lube  hydraulic oil  , for a size to size fit / swivel , also another detail on front wheel bearings , is to washer  up the fit for no sloppy side play  in use , that sloppy side thrust is what tears up those bearings . have heim joint on my pto lever in place of  wobbly trunnion , steering arms , clutch linkage , plow  lever pull rod , solid / smooth . don,t be afraid to make an improvement at any point , once you get over that phase . its easy to make things  very solid / reliable in operation . also like your bearing regrease , stress related grease failure  is common / heat build up , thats why I  hype  hi temp grease, you are on the right track . pete 

 

[KrazeyOlDave 860]

On 1/26/2023 at 9:32 AM, pfrederi said:

 

 

That tire looks a bit narrow for that wheel.

Nah, it’s perfect 

[kpinnc 12,017]

3 hours ago, KrazeyOlDave said:

Nah, it’s perfect 

 

I'd like to see more on that headlight assembly you got there...

[GAJoe 844]

22 hours ago, GAJoe said:

 

I made some new tie rods with grade 7B all-thread in stainless tubing that I had horded.   

I got the tie rods mounted and torqued. Did the greasing of the spindles while up in the air. Greased the steering shaft and the front end pivot.

Hopefully my input seal and belt will get here from Wheel Horse Parts and More so I can get everything back together finally. Got my bearings and seals for the mower deck spindles on order.

Edited January 28, 2023 by GAJoe

[peter lena 8,620]

 @KrazeyOlDave  think the smaller tires are the way to go with potential front end loading /  tire bite , as any of us build up , make a change , you are the guy  doing the work , so your thoughts  are what is going in , made many myself , often  tweaked  as I  check it for function , usually  just a finishing adjustment ,  would not dare to give away any  experimental stuff  I  have done , in enough trouble , pete 

[peter lena 8,620]

@GAJoe  stay at it , thoroughly  verify any changes you make , also related connection points , amazing to me , the functional moving ease that  comes to a trouble spot . done this so often , its like a no brainer , to just do it . heim joints , cable lubrication and spring pull, secure grounding , fuel check valve , on and on . just wonder  how anyone can think that  consistent difficult  issues , is ok and cannot be eliminated .  make it better , pete 

[Heatingman 971]

My heart sank a little about 30 minutes ago, mid plow lost my ability to change gears. Was close to the garage, so I pushed my little B80 back in.

 

All kind of worst case scenario ideas where running through my mind. 

 

Turned out the locking nut for allen screw that holds the gear shifter in place worked loose. 
 

Was able to get it back and going without too much trouble.

Guess I should probably locktite that nut. 
 

Maybe tomorrow. Gotta finish plowing.