D_Mac 8,618 #15176 Posted April 8, 2022 On 4/5/2022 at 8:39 AM, Wheelhorse#1 said: Got the deck sorted out out for the B80.Installed the Mule drive and deck.Ready to try it out on the back 40. Just waiting for the grass to grow now. Deck doesn’t match but that’s all the paint I had for now. I think the deck matches just fine !!! 6 3 Share this post Link to post Share on other sites
JoeM 7,874 #15177 Posted April 8, 2022 Finished up the refurb on the spare 52 incher and took it over to dry storage. I did notice on the el cheapo blades it was embossed "This side to grass". I figure some might need help on that decision. 4 Share this post Link to post Share on other sites
elcamino/wheelhorse 9,297 #15178 Posted April 8, 2022 Spend 2 plus hours cutting a cast pulley off the spindle on a 36 inch RD deck. Soaked it since November trying to loosen the brown weld.Used a sawzall and a cutting wheel , I would send pictures but my camera broke . 3 2 Share this post Link to post Share on other sites
squonk 41,105 #15179 Posted April 8, 2022 14 minutes ago, elcamino/wheelhorse said: Spend 2 plus hours cutting a cast pulley off the spindle on a 36 inch RD deck. Soaked it since November trying to loosen the brown weld.Used a sawzall and a cutting wheel , I would send pictures but my camera broke . Set the spinning cutting wheel on the camera didn't you Waldo! hehe 2 Share this post Link to post Share on other sites
squonk 41,105 #15180 Posted April 8, 2022 (edited) Went to put a new battery in the 1075 Wheel a Matic yesterday. These are a tight fit. Gen belt guard has to come off. The old battery must have swelled some as the top was right against the lower Genny bracket. Had to tug on the battery pretty good to get it out. On the way out it caught the fuel line and pulled it off the tank thanks to the POJ spring steel fuel line clamps. #&+#@^®©!!! Got doused with about a pint of gas. Still soaking clothes in vinegar. Whoever came up with these clamps ought to be in jail! Gladly paid $2 a piece for real clamps. Today new battery slid right in. $29.95 for a 300 CCA at the Mart. Edited April 8, 2022 by squonk 7 2 Share this post Link to post Share on other sites
elcamino/wheelhorse 9,297 #15181 Posted April 8, 2022 11 minutes ago, squonk said: Set the spinning cutting wheel on the camera didn't you Waldo! hehe No Mr. I owe you Mr. Waldo , the camera was only 20 years old , should have worked for 20 more. Did not get my moneys worth.on the camera purchase. Looks like you are going to have to rid in the open trailer. I give up on finding a truck, not paying $20,000 for a 200,000 mile truck. 1 Share this post Link to post Share on other sites
squonk 41,105 #15182 Posted April 8, 2022 2 minutes ago, elcamino/wheelhorse said: No Mr. I owe you Mr. Waldo , the camera was only 20 years old , should have worked for 20 more. Did not get my moneys worth.on the camera purchase. Looks like you are going to have to rid in the open trailer. I give up on finding a truck, not paying $20,000 for a 200,000 mile truck. There are some around here for 35 with 70,000 1 Share this post Link to post Share on other sites
Handy Don 12,218 #15183 Posted April 8, 2022 54 minutes ago, squonk said: $29.95 for a 300 CCA at the Mar Good shopping! 2 Share this post Link to post Share on other sites
nyquil junkie 225 #15184 Posted April 8, 2022 Today I applied a liberal coating of mud and muck to the tires and undercarriage while putting the muck forks to a much harder test. I bent one tooth a wee bit, but overall, it digs pack like a...like a giant pitchfork. 14 1 Share this post Link to post Share on other sites
Wheelhorse#1 1,657 #15185 Posted April 8, 2022 20 hours ago, D_Mac said: I think the deck matches just fine !!! Agreed ! Looks great!.Love what you’ve done there.Unique is a good thing.They all don’t have to be red and white. 2 Share this post Link to post Share on other sites
sjoemie himself 3,068 #15186 Posted April 9, 2022 7 hours ago, nyquil junkie said: Today I applied a liberal coating of mud and muck to the tires and undercarriage while putting the muck forks to a much harder test. I bent one tooth a wee bit, but overall, it digs pack like a...like a giant pitchfork. Is that a PF engineering front end loafers? Looks like it does a good job. 1 Share this post Link to post Share on other sites
D_Mac 8,618 #15187 Posted April 9, 2022 13 hours ago, Wheelhorse#1 said: Agreed ! Looks great!.Love what you’ve done there.Unique is a good thing.They all don’t have to be red and white. Thank you. After I fixed it up I asked @Vinylguyto make me a custom set of decals that would match the original side badging. He knocked it out of the park. I had a red deck at first but decided would look better black. It's been fun making it " different " but still keeping it a true Wheel Horse. 4 5 Share this post Link to post Share on other sites
Lee1977 6,659 #15188 Posted April 9, 2022 Mowing the front yard first lap first turn the off balance 520 lifted the inside rear wheel slid into the ditch hooking the 48" deck in the bank. Tried getting out on the fender no, couldn't get enough traction to back out. Had to go get the C-120/180 and a chain to drag the front up out of the ditch to get the deck clear, then drove it out. Got the yard mowed with the exception of the ditch and side of the road. There was trash out for 100 feet on the side of the road Got a bucket and started picking up the trash. It was busted up electrical boxes and cover plates. Found one new heavy duty receptacle, half a dozen good cover plates, socket half of an out door light, couple of electrical boxes and a couple of stainless steel brackets. I got up all the big pieces 3 Share this post Link to post Share on other sites
entropy 104 #15189 Posted April 9, 2022 Deck work. Blades sharpened. New scalper wheels and a good greasing with marine grease 1 Share this post Link to post Share on other sites
entropy 104 #15190 Posted April 9, 2022 I decided to do a thorough once over. Pulled the manifolds to adjust valves then cleaned up carb (just top off, leaving body on manifold), pulled deck out and angle grinded blades, greased everything, engine oil/trans fluids and filters. 1 3 Share this post Link to post Share on other sites
Wheelhorse#1 1,657 #15191 Posted April 9, 2022 2 hours ago, D_Mac said: Thank you. After I fixed it up I asked @Vinylguyto make me a custom set of decals that would match the original side badging. He knocked it out of the park. I had a red deck at first but decided would look better black. It's been fun making it " different " but still keeping it a true Wheel Horse. I was wondering about the decal.I’ll have to check the @vinylguy out. Almost had a 1075 but someone els beat me to it.The search continues ! 3 Share this post Link to post Share on other sites
davem1111 2,030 #15193 Posted April 9, 2022 I'm working on both the 312-A and the 416-8. Had to do some re-wiring on the 416-8 to get the aftermarket fuel pump to come on when the key is turned on instead of using a separate toggle switch. That works great now. The 312-A, I finally got around to testing the "new" Eaton 7 hydro I put on it, and it doesn't work at all. Posted about this in my thread under Transmissions. I am not very happy about this. 1 5 Share this post Link to post Share on other sites
SylvanLakeWH 25,557 #15194 Posted April 9, 2022 (edited) First cruise around the hood with the E 141. The highly discriminating test engineers rode around in the trailer without ear protection and loved it!!! They like the new locomotive for the SL&WHN RR. Full train testing with maximum loads will commence shortly - once we get more than 15-20 minutes of occasional sunshine… Edited April 9, 2022 by SylvanLakeWH 3 2 7 Share this post Link to post Share on other sites
johnnymag3 2,520 #15195 Posted April 9, 2022 Where are their helmets ??????? Awesome Electric Horse 1 1 Share this post Link to post Share on other sites
lynnmor 7,306 #15196 Posted April 9, 2022 4 hours ago, entropy said: I decided to do a thorough once over. Pulled the manifolds to adjust valves then cleaned up carb (just top off, leaving body on manifold), pulled deck out and angle grinded blades, greased everything, engine oil/trans fluids and filters. It appears that you didn't remove the blades and ground off the bottom, if so that is not correct. The blades need to come off and the angle ground on the top side till sharp. Also, the blades should be balanced and that can't be done while installed. Anyway, your blades are seriously worn and it is time for replacement. 4 Share this post Link to post Share on other sites
entropy 104 #15197 Posted April 9, 2022 Thanks Lynnmor. I did grind both sides, but I did not really think about the balance as well as not really knowing how worn they are(they have been on deck for as long as I have owned and probably well before that I guess...many years). If you do not mind, any recommendations on blades? Also any tips on removal of old blades..... I attempted to remove, but it was so tight I just opted to grind in place 1 Share this post Link to post Share on other sites
kpinnc 12,026 #15198 Posted April 9, 2022 7 hours ago, D_Mac said: It's been fun making it " different " but still keeping it a true Wheel Horse. That could be my motto. None of my tractors are original. And I already talked to Terry about your decals. Mine won't be exactly the same, but I'm copying the look! 3 Share this post Link to post Share on other sites
ranger 1,750 #15199 Posted April 9, 2022 (edited) Gave the C121 a bit of a workout today. Rolled about an acre and a half just to see if it would pull two at the same time. I ended up with three, the 4ft vintage flat roll, the 4ft vintage “Heavy” Cambridge roll, and my homemade flat roll made from an old oxygen cylinder! Even where the ground was really soft and wet I still had traction, (underground spring), grass is always lush, even in a heatwave! Jane videoed me at one point, then it was her turn! I was w.o.t. In 1st high, Jane was w.o.t. In 2nd low. I still have another 3ft Cambridge roll I could add to the “Train”, but reversing would be a b***h! 2B9BFF93-13C7-4090-BB6E-BB10792087BD.MOV Edited April 9, 2022 by ranger 7 4 Share this post Link to post Share on other sites
ebinmaine 67,492 #15200 Posted April 9, 2022 4 minutes ago, ranger said: the C121 On those front AG tires. I'm curious to know if you've ever run them the other direction. I've read that having AGs on a non drive axle like yours, they should be "reversed" as you have them. Do you find that they work well? Thoughts comments suggestions. .... 2 Share this post Link to post Share on other sites