What have you done to your Wheel Horse today?

[Pullstart 62,870]

Finally got to play with my Snowmotractor last night.  There’s some work to do, but it moves and the first test run was a success!

 

 

[BHunter 1,700]

3 minutes ago, Pullstart said:

Finally got to play with my Snowmotractor last night.  There’s some work to do, but it moves and the first test run was a success!

 

Looks so fun . You are a wild man! That bucking horse almost through you off on that one landing . Congrats on completing your build. It’s very cool. 

 

[Ed Kennell 38,173]

But, will it plow snow?

[rjg854 11,361]

It's not about how fast you plow, it's about how fast you plow well.         

[Pullstart 62,870]

6 hours ago, Ed Kennell said:

But, will it plow snow?

If it’s grille high?  Yep.  

[Lee1977 6,659]

16 hours ago, Ed Kennell said:

But, will it plow snow?

If he gets it geared up it should throw two roster tails of snow.

Edited February 12, 2022 by Lee1977

[Sparky-(Admin) 21,317]

  Finally got both hubs pulled back out to where they should be on my 867. 
  She’s a “wide ride” now 

 

 

 

[Lee1977 6,659]

Here is what I did to the hubs on my 312. We rekeyed the hubs to the other set screw hole as the original had gotten larger on each side of the key.  Then we rekeyed the axles to a full length square key way  To finish it off I added split collars to the inside of the hubs and tighten them down tight.

Edited February 12, 2022 by Lee1977

[Oldskool 6,644]

Well we had a good warm day so took Hiram out for a spin.

Using the split brakes and chains a bit to rough up our skating rink of a driveway.

[Horse Newbie 7,069]

I replaced the bulb in my tachometer on the 1994 520H, and also did the LED headlights upgrade.

 

On the first video, wait for it…

Edited February 13, 2022 by Horse Newbie

[kpinnc 12,028]

39 minutes ago, Horse Newbie said:

On the first video, wait for it…

 

Thought my phone died for a minute... Those look great! 

[kpinnc 12,028]

I fixed my Bronco's throttle cable. I've changed it several times, but they eventually break loose and get stuck in the lock position.

 

Horror Fright carries a couple different roll pin assortments. Both have 1/16th pins. So I cross drilled the knob though the shaft, and stuck a pin in it. Used small channel locks to press it in.

 

Time will tell, but so far it's great!

 

 

Edited February 13, 2022 by kpinnc

[Lee1977 6,659]

5 hours ago, kpinnc said:

I fixed my Bronco's throttle cable. I've changed it several times, but they eventually break loose and get stuck in the lock position.

 

Horror Fright carries a couple different roll pin assortments. Both have 1/16th pins. So I cross drilled the knob though the shaft, and stuck a pin in it. Used small channel locks to press it in.

 

Time will tell, but so far it's great!

 

 

Looks good you have it fixed unless the plastic nob breaks. I use the choke nob off my Vanguard on my 312. The finish on mine isn't hold up too well might need to paint it.

 

[kpinnc 12,028]

2 hours ago, Lee1977 said:

I use the choke nob off my Vanguard on my 312.

 

Nice! Never thought of that one! 

[Ifixoldjunk 778]

I had to unwillingly beat the snot out of the poor 310 today. Got hit with a surprise 4 inches of snow overnight that landed right on top of my muddy gravel driveway. Last week was a heat wave and the ground didn’t have a chance to solidify. Sucked up more mud and gravel than I wanted too.

[Lane Ranger 10,968]

Had to change plug and boost battery to start the B-80 in 15 degrees!  It was 12 most of the night and my garage is not heated.

 

Trailer was frozen!  Rammed it loose!  Then couldn’t move on front hitch so put on rear and was able to move.  Cold! 

All of this to get ready to head south to Florida Flywheelers next week. 

[Ifixoldjunk 778]

@Pullstart holy smokes that looks good. Now you’ve got me eyeing up my poor firewood hauler bolens. Help it navigate the snow better.😅

[pfrederi 17,739]

Plow time you will still turn up rocks but they will be in neat lines at eh edge of the driveway

[Pullstart 62,870]

@Ifixoldjunk if you toss too many rocks, I’ve seen people use a shop vac in their yard come spring time to get them outta the grass 

[Ed Kennell 38,173]

1 hour ago, pfrederi said:

Plow time you will still turn up rocks but they will be in neat lines at eh edge of the driveway

 

 

                                                          Main reason I switched from blowers to plows.   

 I also found when the snow starts to melt, I plow the snow edges back on the road and as the snow melts, the gravel is deposited where it belongs with very little raking.

[kpinnc 12,028]

Had to swap a wheel bearing tonight. Had these lying around. Probably overkill for these little tractors, but outta last a while...

 

Direct axle contact, but over an inch wide. We'll see how they do.

[Snoopy11 5,714]

1 minute ago, kpinnc said:

Had to swap a wheel bearing tonight. Had these lying around. Probably overkill for these little tractors, but outta last a while...

I made a whole thread over those babies!!! STILL going strong.

 

 

Don

[Dstegjas 29]

Nothing big, just put a pair of new front tires on my 310-8. It still had the original tires on it. I can’t complain after getting 34 years out the them. 
 

Jim

[Horse Newbie 7,069]

11 minutes ago, Dstegjas said:

Nothing big, just put a pair of new front tires on my 310-8. It still had the original tires on it. I can’t complain after getting 34 years out the them. 
 

Jim

What brand ?

[Renrag 69]

Well poop changing engine on my B115 the clutch housing got stuck to where I had to beat it off, well it came off, but not unscathed. The part of it where the belt rides half the lip broke off the cast, so idk if it's still usable or not. The drive belt fits really tight, but it's the rubbing and wear it'll cause drive belt is my worry. Anyone that would have a spare clutch housing for my little horsey I would be interested.