Jump to content
Shea Worden

Belts

By Shea Worden, in Wheel Horse Tractors

Recommended Posts

Shea Worden    40

Shea Worden
Posted

Where can I find a good new drive belt for my wheel horse? I cant seem to find any online or anywhere else. I figured I would run it by you guys and see what surfaces.

Share this post

Link to post
Share on other sites
 

953 nut    55,092

953 nut
Posted

Take your old one to Tractor Supply and have them match it up to a new Kevlar belt.

  • Like 3

Share this post

Link to post
Share on other sites
 

Shea Worden    40

Shea Worden
Posted

Thanks. 953 nut, I didnt know that they did that. I have a few belts to match up. 

  • Like 1

Share this post

Link to post
Share on other sites
 

fast88pu    3,324

fast88pu
Posted

Toro dealer. Replace it with an original belt. They do make a difference if you plan on pulling anything with it. 

  • Like 2

Share this post

Link to post
Share on other sites
 

squonk    41,037

squonk
Posted

I have had 0 issues with TSC and Napa Kevlar belts for 30 yrs. doing any job asked of the tractor. Drive,mower, blower it doesn't matter. Just make sure you get the proper width as well as length.

  • Like 3

Share this post

Link to post
Share on other sites
 

fast88pu    3,324

fast88pu
Posted
5 hours ago, squonk said:

I have had 0 issues with TSC and Napa Kevlar belts for 30 yrs. doing any job asked of the tractor. Drive,mower, blower it doesn't matter. Just make sure you get the proper width as well as length.

TSC belts aren't what they use to be then. I had 3 go on my 48" deck mowing this season. I will be sticking to the factory belt. 

  • Like 1

Share this post

Link to post
Share on other sites
 

953 nut    55,092

953 nut
Posted

Got to agree on the mower drive, haven't had the best results with Kevlar there ( one year and need replacement), but for drive belts to the transmission I have been very pleased with Kevlar.

  • Like 1

Share this post

Link to post
Share on other sites
 

squonk    41,037

squonk
Posted

I have 5 yrs on my Napa green PTO belt. Probably will install a new one next year. The only :wh: OEM belt I have in the fleet is the belt that came on my snow blower.  

  • Like 1

Share this post

Link to post
Share on other sites
 

Shea Worden    40

Shea Worden
Posted

How do I know if i am over working my trans? If I spin my wheels?

Share this post

Link to post
Share on other sites
 

953 nut    55,092

953 nut
Posted

Spinning your wheels is no problem. If your wheels had enough traction to never spin then the next weakest link would rear its ugly head and brake so a lack of traction is sort of a safety valve.

  • Like 1

Share this post

Link to post
Share on other sites
 

fast88pu    3,324

fast88pu
Posted
14 minutes ago, 953 nut said:

Spinning your wheels is no problem. If your wheels had enough traction to never spin then the next weakest link would rear its ugly head and brake so a lack of traction is sort of a safety valve.

I broke a belt pulling last year. Had tons of traction lol

Share this post

Link to post
Share on other sites
 

Shea Worden    40

Shea Worden
Posted (edited)

Thanks. my tractor looses traction pulling heavy stuff where I feel like something would break.Now I know that I wont bust my 8-speed tranny. 

Edited by Shea Worden
  • Like 1

Share this post

Link to post
Share on other sites
 
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Go To Topic Listing

  • Similar Content

    • Rob R
      C81 Mower Drive V Belt
      By Rob R
      Hi Guys my C81 has a 38 dual blade, side discharge mower deck (# 0537SC01) The deck belt also goes around the mandrels through the mule drive and also to the PTO so it's a huge belt. The current belt is stretched and ready to go. I believe it is around 1/2 X 142 inches but not sure was hoping one of you might have the correct size. Much appreciated. Rob 
    • Bill D
      Look what I found at Lowe's
      By Bill D
      Found these at Lowe's.  Same belts as TSC, just different packaging.  The 86" I got was on clearance and is not being stocked anymore.  They had sizes from 87" to 109" in 1/2".  Not a lot of 5/8" belts that would be useful for our tractors.



    • Ifixoldjunk
      42 inch rear discharge belt sizes?
      By Ifixoldjunk
      I just bought a deck for my 310-8, it’s a 42inch rear discharge, it came with a complete parts tractor, but I need new belts for it. Does anyone know what size belts I need?
    • Tim Fenn
      C125 PTO Drive Belt for 42in Mower Deck
      By Tim Fenn
      I've just acquired a renovated C125 but unfortunately the drive belt got snagged with the mower deck belt (maybe because of incorrect fitment?). It looks like I'm on a steep learning curve! I've been trying to find out which belt to buy as a replacement. The belt I've just taken off is 94 inches but  according to the parts manual I need a Toro belt part number 94 2501 which is 103 inches? The mower deck is a 42in rear eject. It's funny that the Toro belt has 94 2501 as the part number but is 103 inches & I apparently need a 94in belt? Any ideas? 
    • Shea Worden
      8 speed transmission problem
      By Shea Worden
      Hey guys, my wheelhorse c81 got a new transmission last year and now it’s grinding when I drive. First thing the brake pulley is on a higher shaft and doesn’t work with the c81 brake rod and hardware. Second the bearing behind the intake pulleyhas fallen out, which I assume is the grinding sound. Is there a way I can fix it without taking the whole transmission apart? I don’t have enough knowledge to do that kind of repair. Thanks so much -Shea 
×
×
  • Create New...