Jump to content
Tractor boy

help needed!

Recommended Posts

Tractor boy

Ive been trying to change the headlight bulbs on my 312-8. but i cant seem to get the glass cover off. So are these bulbs change able? And is there a reason for the headlights to not function if they are getting current?

- Tractorboy

Share this post


Link to post
Share on other sites
 
BaySide1

I changed the bulbs in my 520H a few months ago. There were no glass covers.

Post a pic of what your looking at.

 

image.png.a7508f3bb80fc84e1a34ab60df177393.pngJust undo the clips at the 3 O'clock position and they pop right out

Edited by BaySide1
  • Like 2
  • Excellent 1

Share this post


Link to post
Share on other sites
 
953 nut

 

4 minutes ago, Tractor boy said:

is there a reason for the headlights to not function if they are getting current?

Yes, the bulb is bad.They are a sealed beam headlamp, take the old one to an auto parts store and they can fix you up.

  • Like 3

Share this post


Link to post
Share on other sites
 
BaySide1

NAPA has the bulbs for like $7.00 each

  • Like 1

Share this post


Link to post
Share on other sites
 
N3PUY

OR ..... the bulbs have a poor ground.   If the ground wire for the bulb is attached to the hood there could be no ground.  When the ground is the hood, the circuit must pass thru the hood hinge to get back to the battery.  That's a bad connection.  There needs to be a jumper wire from the hood to the tractor frame.  If you're using a test light connect the alligator clip to the ground side of the bulb and probe the (+) side of the bulb.  Got light?  If not you'll need to fix the ground.  If the test light came on you'll need bulbs!

 

5994b2f7bda82_HLground.png.880144e78e0c52594c3b32339679c4e5.png

Edited by N3PUY
  • Like 6

Share this post


Link to post
Share on other sites
 
Tractor boy

I got the headlights off the hood. there is a glass lenses covering in front of the bulbs. i was wonder as how to a individual would go about removing this glass lenses? Yes i have that kind of ground, but it worked fine before.

Share this post


Link to post
Share on other sites
 
CasualObserver

The glass lens IS the bulb... the element inside is not a serviceable part. Take it to the auto parts store and get the replacement... they're cheap.... well I see you're in CT... so perhaps not quite so cheap! ;):lol:

  • Like 7

Share this post


Link to post
Share on other sites
 
953 nut

This is what a sealed beam headlight looks like. It is a one piece replaceable unit. You don't remove "the bulb", it is a sealed unit.

Image result for sealed beam headlights

  • Like 5
  • Excellent 1

Share this post


Link to post
Share on other sites
 
Digger 66

X-2 ^^ 

And don't bother replacing them with the LED's that are an exact replacement .

I did on the snowblower that's at my mom's house and couldn't be more disappointed ,

They advertise that it's equal to a 50 W halogen .

Bullllll ! 

it looks like a candle and will probably outlive ME :blink:

 

https://www.amazon.com/gp/product/B00SFCJ01A/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1

  • Like 1
  • Thanks 1
  • Sad 1

Share this post


Link to post
Share on other sites
 
TDF5G

The easiest way to test those is to connect the terminals of the sealed beam to a 12 volt battery with a jumper wire.

 

Edited by TDF5G
  • Like 3
  • Excellent 1

Share this post


Link to post
Share on other sites
 
Tractor boy

Thanks for all the help. So i should disconnect the lights and replace? 

Share this post


Link to post
Share on other sites
 
WHX??

If there is not a bad ground and you are getting power to them yes. If you have a multimeeter you can ohm them out to make sure they are not bad.

 

On ‎8‎/‎16‎/‎2017 at 5:33 PM, Digger 66 said:

don't bother replacing them with the LED's that are an exact replacement

Is that right @Digger 66 ? I was groining to pull the trigger on a pair of them for the 520. Keep the amp drawn down so I could run those and the hi-test cab lights. Nice to know they're not worth a hoot. Looks like they good reviews?

  • Thanks 1

Share this post


Link to post
Share on other sites
 
BaySide1

you could always try am LED light bar

00u0u_lnQ5qBXjU3m_600x450.jpg

  • Like 3

Share this post


Link to post
Share on other sites
 
lynnmor

I just felt a lot older, these young wippersnappers don't know about sealed beam headlights. Now we have the plastic junk that fogs and costs a fortune to replace.

  • Haha 1

Share this post


Link to post
Share on other sites
 
Digger 66
2 hours ago, WHX12 said:

If there is not a bad ground and you are getting power to them yes. If you have a multimeeter you can ohm them out to make sure they are not bad.

 

Is that right @Digger 66 ? I was groining to pull the trigger on a pair of them for the 520. Keep the amp drawn down so I could run those and the hi-test cab lights. Nice to know they're not worth a hoot. Looks like they good reviews?

 

I don't care for it . It's white , yes . But as for illuminating the work area ? It gets a 3 out of 10 .

 

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • WheelPuke
      By WheelPuke
      I have my 25A fuse blowing every time I put a new one in the slot. The old one was burnt up when I got the tractor put this year. It sat for a year with a dead battery. I stopped using it as much because the transmission is clattering pretty bad when taking off on second or higher. I had to replace the clutch belt a few years ago and couldn't get an OEM. Not sure what is the problem there that's another issue though.
       
      I have checked the wiring and patched the worn spots where it could be grounding out. The fuse blows as soon as there is power to the system with the ignition off. I'm at a loss of what to check for at this point. Any input from someone who has had this issue would be appreciated. I'm not sure what these units are in the photos but do not know how to test them for a failure. They are directly in loop with the battery and the ignition loom looks to run into that 25A fuse.

    • BrianKoch
      By BrianKoch
      Hello gentleman, 
       
      Problem: will not crank on its own, will crank with jump box—but still not fire
       
      Recent things I did prior to this issue: cleaned fuel filter, replaced battery cables, replaced cable from ignition to starter
       
      I have my test light out and am probing around. 
       
      There is no power at ignition/magneto wire or the ignition/starter wire
       
      There is power everywhere else






    • Jeff-C175
      By Jeff-C175
      Detailed wiring from the Demystification Guide #492-4509
      4 pages 1.4MB Color
      p7-67 to p7-70
       
      Onan powered
       
      1989 416-8 model 31-16O801
    • trident
      By trident
      Need some help. My 800 Special has an electric PTO. It is not working. Checked Ohms - nothing. My questions are 1) how does the PTO come off and 2) can they be rebuilt? I took the bolt out that I thought holds it on but no luck. Must be something more?
    • grasscuts
      By grasscuts
      Hi, here's what happened. I changed out 9 pin moles plug...had issues tracter quit running and changed the plugs while I was at it....got plugs from auto store cross reference to ngk they said it was the same heat range and I check electrod  length with calipers ,same...tracter started right up and ran great for about 10 min. And started back firing and quit.....going to check it out tonite anybody have an idea?    
×
×
  • Create New...