Jump to content
Rozlo

New wheels for my 314 Hydro

By Rozlo, in Wheel Horse Tractors

Recommended Posts

Rozlo    6

Rozlo
Posted

Cub Cadet 582 682 782 23x10.5-12 ag tires and rims  Looking to see if these will fit my tractor.

Need some advise.

 

 

 

 

 

 

 

s-l1600.jpg

Share this post

Link to post
Share on other sites
 

WVHillbilly520H    10,373

WVHillbilly520H
Posted

Should be fine, use a tape measure and something for straight edge across the tire to check your backspacing on your WH wheels, then the CC wheels just to be sure you have enough clearance for the hydro fan ect, Jeff.

Share this post

Link to post
Share on other sites
 

cschannuth    3,816

cschannuth
Posted

I don't think hub caps will work with those valve stem locations.  That's obviously not an issue if you don't plan to ever install caps.

 

Craig

Share this post

Link to post
Share on other sites
 

WVHillbilly520H    10,373

WVHillbilly520H
Posted
7 hours ago, cschannuth said:

I don't think hub caps will work with those valve stem locations.  That's obviously not an issue if you don't plan to ever install caps.

 

Craig

They'll just have to be the IH ones if you can find them, Jeff.

Screenshot_20170815-045747.png

  • Like 1

Share this post

Link to post
Share on other sites
 

shallowwatersailor    3,213

shallowwatersailor
Posted

I had a 582 at one time  and, depending on the model, you will find the backspacing is different than a Wheel Horse wheel. Like Jeff said, measure the backspacing. You could use a pair of spacers to make up the difference.

  • Like 1

Share this post

Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Go To Topic Listing

  • Similar Content

    • robertsonchris06@gmail.co
      8-25 Riding mower belts
      By robertsonchris06@gmail.co
      After using my 8-25 mower successfully for several years I noticed the belts were very worn. I replaced the belts and used the mower several mowings this past summer with no problems until as I was mowing the last time the mower would not move in any gear. After stopping and inspecting the traction belt it was almost completely destroyed. Prior to this I had noticed that the engage/disengage lever was getting hard to activate (very stiff). Has anyone had a similar thing happen?
      Thanks in advance for any help on this problem.
      Just want to keep my mower running.
      Chris
    • MachXXII
      1988 252-H Wheels
      By MachXXII
      I’m trying to restore my grandfathers old 252-H to use around my property. The tires are shot and the rims aren’t too far behind. Anyone have any recommendations for rims and tires that would fit well on it? 
       
      right now it has 22 x 7.50 - 12 on the back and 15 x 6 - 6 on the front.
    • 87buickt
      Snow thrower help
      By 87buickt
      Newb here, recently purchased a b310 that now runs with snow thrower, plow, and mower deck for what I believe to be a good deal for $200. My question to all y’all gurus is what am I missing for my snow thrower attachment? I’d like to get it squared away before winter I know I’m going to need a belt and chain any help would be greatly appreciated. 



    • Redcube
      How do Identify my tractor
      By Redcube
      I need help Identifying my wheelhorse tractor model number 105109 I don't know how to read it
    • Samone
      First mow / no PTO
      By Samone
      I recently acquired a 520xi. She's a pretty sweet machine and I took a liking to her before she landed in my garage. I've used her a few times this spring to haul some brush around in her trailer. 
         As the grass grew taller, however, I knew it was time to put the deck on her and start mowing. Note: this is my first wheelhorse, and also this was the first time I'd mown with her. Anyway, I did about half an hour of mowing (about half of my lawn), having turned her pto on and off a few times for various reasons, when at some point I turned the pto off to back out from between the dead-end swath between 2 trees I had just mown. I backed out, turned around, lined myself up to get back on track with the mowing, pulled the pto knob, and....nothing. Or so I thought at first.
         There is a quiet, though definitely present sound whenever I pull the pto knob on. At first I thought the blades might be stuck or something and the drive belt was sliding on the pto pulley. After some inspection, I found it wasnt. I prooved it wasn't by taking the drive belt off the pto and trying to turn the pto on. I still hear that same sound and the engine acts slightly stressed when I turn the pto on.
         One last thing. I turned the engine off, took the front grill off the tractor and tried to turn the pto pulley. It moves but is stopped by some kind of what looks like a safety stop (a bar on the pulley hitting a bar in the way). 
         Anyway, this is where I'm at. If anyone knows or has any idea why what's happening is happening and/or how to fix it Id appreciate it very much.
        
×
×
  • Create New...