Jump to content
Danny856

Looking for a belt....

By Danny856, in Implements and Attachments

Recommended Posts

Danny856    2

Danny856
Posted

Hey guys, I'm sure the answer is somewhere on this site but for the life of me I can't find it. I have an '89 Wheel Horse 310-8 (210K806) and my mowing deck is 0542MR04. I need the belt that connects the two. The one that goes from the engine/mule drive (?) down to the deck. It kept poppin off. I thought I finally had it set right but then it came off again and I ran over it. Can anyone help? Thanks in advance. Dan. 

Share this post

Link to post
Share on other sites
 

rmaynard    15,907

rmaynard
Posted (edited)

Dan,

 

Here is the info you need:

 

Drive belt 108834 (1/2" x 98") [Replaces 102741 as per PSB #272 in this application]
Spindle belt 106125 (1/2" x 89.03")

 

 

 

 

 

and :WRS:

Edited by rmaynard
  • Like 3

Share this post

Link to post
Share on other sites
 

Achto    28,688

Achto
Posted

:WRS:  Looks like rmaynard  has you covered.

  • Like 1

Share this post

Link to post
Share on other sites
 

Tankman    3,520

Tankman
Posted (edited)

:WRS: Maynard has your belt info. Right on!

TSC (Tractor Supply) has Huskee Kevlar belts on the rack, inexpensive. Never had one fail.

Magic Marker the sleeve, "310-8 42" RD deck, drive". Staple the belt sleeve to the shop wall.

 

Girls don't pump gas in New Joisey.

Edited by Tankman
  • Like 1

Share this post

Link to post
Share on other sites
 

Danny856    2

Danny856
Posted

Thanks guys! I knew I came to the right place :)

  • Like 2

Share this post

Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Go To Topic Listing

  • Similar Content

    • Fordiesel69
      WANTED: OEM Muffler for Kohler Magnum M10 thru M16
      By Fordiesel69
      Looking for the OEM nelson muffler that fits the Kohler Magnum M10 thru M16 engines found on the following tractor list:
       
      310-8
      310-H
      312-8
      312-H
      314-8
      314-H
      410-8
      410-H
      412-H
      412-8
      414-8
      414-H
      416-8
      416-H
      and also and "A" models that had the kohler magnum.  
       
      I dropped mine off to be welded and it came up missing.  It was not good to begin with so im sure they accidentally tossed it out with the way it looked. 
    • 87 312-8
      Hhookatrophy
      By 87 312-8
      looking for mule drive bearings for a 36 inch rear discharge deck 1986/87 312-8, thank you
    • OHLB
      Won't start
      By OHLB
      Newbie here. 310-8 won't start. Battery is dated 10/19. Did crank a couple times but started losing ummph. Should I replace it or attempt to charge it? Can't tell if the battery is frozen. Never knew until today that batteries could freeze and that it's dangerous to charge a frozen battery. It's been single digits with wind chill the last couple weeks here. 
    • Big Rig
      Clutch Neutral Safety Switch
      By Big Rig
      ISO clutch neutral safety switch for 310-8
      or alternative 
    • Rob R
      310-8 Speed & Drive Belt Change
      By Rob R
      Soo couple of years back did a pulley change on the tranny from 6 inch to 4.5 and used a 1/2 X 79 belt to make it work and it worked fairly well but wanted to get back to a 5/8 drive belt so went to a 5/8 x 81 inch belt and added a second flat Idler pulley. I simply cannot believe how smooth and sharp it shifts and drives now!  The added flat Idler was 2 3/4" with a 5/8ths bore used and existing hole on the side shroud and just opened it up a bit. I use to slip a bit on steep hill with the 79" slips no more, the belt drives and the clutch is  LOT smoother and in the right pedal area.... Will see how it holds up cut 3/4 of an acre of grass yesterday NO issues. 





×
×
  • Create New...