Bigger drive pulley.. now it's slower?!?

[cschannuth 3,816]

35 minutes ago, Team70R said:

I did the same with my predator swapped 606!! Love it!!

 

It is a lot of fun. I was worried about it robbing too much power but that thing is really good at low RPMs out of the hole too. To start out in high gear I have to throttle it down to almost idle or it will pop a massive wheelie. 

 

Sorry. I didn't mean to hijack this thread. 

Edited January 10, 2017 by cschannuth
Apology

[daveoman1966 3,750]

I wanna play too....   This is from somewhere...don't know

Clik it, then change pulley diameters and watct... 

http://www.blocklayer.com/pulley-belteng.aspx

[953 nut 55,173]

13 hours ago, 953 nut said:

If you had a bike as  a kid you know the front sprocket was bigger to gear it DOWN   UP to the rear wheel so you could peddle it with ease; same deal here.

Seems like i didn't think very much prior to typing!   

[Team70R 157]

9 hours ago, cschannuth said:

 

It is a lot of fun. I was worried about it robbing too much power but that thing is really good at low RPMs out of the hole too. To start out in high gear I have to throttle it down to almost idle or it will pop a massive wheelie. 

 

Sorry. I didn't mean to hijack this thread. 

I had to build a front weight bracket after I almost flipped it!! 

[Ed Kennell 38,122]

1 hour ago, 953 nut said:

Seems like i didn't think very much prior to typing!   

 

We all been there and done that Richard.    Although I'm thinking you had a plan to start a really good discussion....and I worked. 

[953 nut 55,173]

5 minutes ago, Ed Kennell said:

I'm thinking you had a plan to start a really good discussion.

No,  !

[Team70R 157]

Anyone know where to find a pulley with a metric keyway? The Honda shaft is a 1" diameter with a 7x7mm key!!  can only find 1/4" around here!

[953 nut 55,173]

NAPA should have them, with all the metric junk out there I'd be surprised if they didn't. Any dealer that sells and services Honda or other ATVs will have them.

[Team70R 157]

41 minutes ago, 953 nut said:

NAPA should have them, with all the metric junk out there I'd be surprised if they didn't. Any dealer that sells and services Honda or other ATVs will have them.

Well we determined the cause of the slow drive speed is from the gear reduction on the motor   I never realized it had one. 

[Ed Kennell 38,122]

So, if you know the real drive shaft RPM of the Honda, you can use daveoman's link to determine how large the drive pulley needs to be to achieve the same speed you had with the Techy.

http://www.blocklayer.com/pulley-belteng.aspx

[Ed Kennell 38,122]

On ‎1‎/‎9‎/‎2017 at 9:13 PM, Team70R said:

Ed,

 Looks like I'll be able to solve my problem easier than you will be able to solve your Elks problem haha. If I had any advice I'd certainly pass it on to you!

 

Thought this deserved an update...... Our ELKs lodge is now smoke free during Friday night dinner hours. 

[SylvanLakeWH 25,525]

2 minutes ago, Ed Kennell said:

 

Thought this deserved an update...... Our ELKs lodge is now smoke free during Friday night dinner hours. 

 

Congrats on your victory!

[953 nut 55,173]

8 hours ago, Ed Kennell said:

ELKs lodge is now smoke free during Friday night dinner hours.

Congratulations;    it should be all the time.