buffaloman 295 #1 Posted October 20, 2016 (edited) made me a little wheel horse work bench out of some repurposed oak ,and these old table legs I had laying around , urethaned in a logo sticker I picked up at the show . I couldn't wait to take a picture those white milky streaks are there because its not dry yet Edited October 20, 2016 by buffaloman 17 Share this post Link to post Share on other sites
857 horse 2,581 #2 Posted October 20, 2016 Gezzzz Louiggi...........that is off the chain!!!!!!! Good idea...... How is "RED" coming along.?? lol Share this post Link to post Share on other sites
buffaloman 295 #3 Posted October 20, 2016 2 minutes ago, 857 horse said: Gezzzz Louiggi...........that is off the chain!!!!!!! Good idea...... How is "RED" coming along.?? lol lol. unfortunately no updates ,just gotta put a motor on an figure out how to make it work , 1 Share this post Link to post Share on other sites
857 horse 2,581 #4 Posted October 20, 2016 what do you want to do for an engine.?? just somthing small.?? Share this post Link to post Share on other sites
tunahead72 2,439 #5 Posted October 20, 2016 1 hour ago, buffaloman said: I couldn't wait to take a picture those white milky streaks are there because its not dry yet You know, if you hadn't mentioned the streaks, I wouldn't even have noticed, it's just a cool looking table to me. How wide are those two larger boards? 2 Share this post Link to post Share on other sites
buffaloman 295 #6 Posted October 20, 2016 (edited) They are 13x2x33 i cut about 3inches off each end of the metal legs to get the whole table roughly. Around 32 square but its not square Edited October 20, 2016 by buffaloman spelling 1 Share this post Link to post Share on other sites
buffaloman 295 #7 Posted October 20, 2016 Final pic now complete with some reclaimed barnwood from my grandfather's barn added for shelve on the bottom 5 Share this post Link to post Share on other sites
tunahead72 2,439 #8 Posted October 20, 2016 Very nice! Are the 13" wide boards also from a barn? 1 Share this post Link to post Share on other sites
DougC 2,641 #9 Posted October 20, 2016 Always nice to have a good heavy duty work surface. 2 Share this post Link to post Share on other sites
buffaloman 295 #10 Posted October 20, 2016 4 hours ago, tunahead72 said: Very nice! Are the 13" wide boards also from a barn? No the top boards were from a big oak plank my father in law had ,he used it to roll drums of oil on and off his truck , those I actually sanded there was a lot of green and red paint on them ,I left the underside of the boards untouched 20 hours ago, 857 horse said: what do you want to do for an engine.?? just somthing small.?? I picked up a Clinton 700A I found on craigslist for $35 guy said he couldn't keep gas in it or something , I brought it home put gas in it pulled it one time and it started right up. theres nothing wrong with it .might use that I also have a Clinton B700 that I could use and my father in law has two really small briggs Share this post Link to post Share on other sites
857 horse 2,581 #11 Posted October 20, 2016 If either Clinton fits...that would be a great idea.....If it dont and one of the briggs will fit,....that might be the best 2nd bet.....you are at the point i was,,,,,i had to figure out how to make my engine belt to clutch,,,,,,,works Ok,,,now....,,,,,,,,,,if every thing has pul;leys,,,,see if they will line up.....i can send pics ....if that would help.. ... 1 Share this post Link to post Share on other sites
