Jump to content
elicountryboy1996

wheel horse bushing

By elicountryboy1996, in Transmissions and transaxles

Recommended Posts

elicountryboy1996    2

elicountryboy1996
Posted

I have a wheel horse c-161 automatic hydro, And I was plowing with it, there is a small bar under the seat that swings back and forth with the hydraulics and it is attached to a circular piece with 2 bushings that have a small flange on the end of them, they are both pretty much shot and the one flange broke off so I could no longer raise my plow because the piece holding the bar with the bushings popped out because the one bushing is completely shot, Anybody Know where I can get these small bushings?

Share this post

Link to post
Share on other sites
 
 

oldredrider    2,550

oldredrider
Posted

I think he's referring to the bushings in the rear rock shaft. If not available from Partstree,  you might try your local Ace hardware.

Share this post

Link to post
Share on other sites
 

Ed Kennell    38,744

Ed Kennell
Posted

:text-yeahthat: Pretty sure ACE and TSC have the flanged bronze bushings.   3/4 X 1" sounds  familiar  but check your shaft and holes.

  • Like 1

Share this post

Link to post
Share on other sites
 
 

elicountryboy1996    2

elicountryboy1996
Posted

It is indeed the clevis hitch and I was able to get the bushing/bearing pieces at ACE hardware, they arent factory but they get the job done, thanks for all your help guys

  • Like 1

Share this post

Link to post
Share on other sites
 

Ed Kennell    38,744

Ed Kennell
Posted (edited)

What is the current ACE price?    I think they have a slightly thicker flange than the TORO part.

 

BTW,  :text-welcomeconfetti: to :rs:        Good to hear from another PeeeeAaaaer.

Edited by Ed Kennell
  • Like 1

Share this post

Link to post
Share on other sites
 

elicountryboy1996    2

elicountryboy1996
Posted
On 8/27/2016 at 0:33 PM, Ed Kennell said:

What is the current ACE price?    I think they have a slightly thicker flange than the TORO part.

 

BTW,  :text-welcomeconfetti: to :rs:        Good to hear from another PeeeeAaaaer.

I payed like 7 Bucks for 2

Share this post

Link to post
Share on other sites
 

ol550    830

ol550
Posted

Check the vender section. Wheelhorseman1000 has them on his site.

  • Like 2

Share this post

Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Go To Topic Listing

  • Similar Content

    • davidfindlay
      1984 C Series, dump trailer and leaf impeller
      By davidfindlay
      Looking to find a new home for my 84 (I think) C-145. It has a dump trailer with the enclosure for leaves, the PTO impeller to get the leafs into the trailer, the hoses for deck-to-impeller, impeller-to-trailer.
       
      I haven’t run it in over a year.
      The battery and the cable to the battery probably need to be replaced.
      Comes with a new head gasket still in the bag.
      Seat is cracked but still comfortable.
       
      Happy to answer questions or take other pictures.















    • 87 416-8 horse
      Wanted wheel horses
      By 87 416-8 horse
      I’m looking for wheel horse tractors for sale or for parts in the Eastern Nebraska or western Iowa area. Preferably 8 speed manuals. Pm me or comment with what you have. The worst I could say is it’s out of my price or distance range. Edit: engine is not important, it’s going to get an engine swap.
      Thanks,
      John
    • BrianStasC-101
      predator 420 pto
      By BrianStasC-101
      Hello all. I am looking for suggestions on adapting the pto from my C series tractor to a harbor freight predator 420 13hp engine. I know the predator motors are a controversial topic however it is the route I have chosen for this particular machine. The intent was to mostly use it for plowing so no PTO required but it would be handy to have. Looking to hear from someone that has successfully done the swap that may offer any advice before I attempt to transfer it over. Just looking for any general pointers that will help me along the way to make it go as smoothly as possible. 
    • HumbleHans
      Tractor 1984 C -Series OM Wiring Rev.pdf
      By HumbleHans
      Operator manual 810343R1
      Wiring
      34 pages 17.5MB
       
      Wiring Colored 
      1 page 228KB
       
      1984 C-105 8-Speed model 11-10K802
      1984 C-125 8-Speed model 11-12K802
      1984 C-145 Automatic model 11-14KE01 - Some used alternate inner axle bearing See PSB #369
      1984 C-165 8-Speed model 11-16K801
      1984 C-175 Twin Automatic model 11-17KE01 - Some used alternate inner axle bearing See PSB #369
      1984 C-195 Twin Automatic model 01-19KE02
       
       
    • t_furl43
      1979 C-101
      By t_furl43
      1979 c-101 nice project tractor just needs a few odds and ends, steering wheel, coil, carburetor bowl, the wiring was redone by previous owner....all 4 tires are good and hold air it goes into all gears no problem, transmission fluid has been changed, 10hp Kohler, message me or call or txt with any questions, it does run and runs well,  it’s been kept inside since I’ve had it, I would also trade for a mid mount grader blade thanks 




      92DB561C-FF95-4868-A52B-5725D4D3B9DE.mp4
×
×
  • Create New...