1277 DASH DECAL BRUSHED CHROME

[Vinylguy 4,687]

Sarge sent me this 1277 dash all blasted and primed.

got busy and designed a template last night and made a few prototypes today.

this is his dash with the decals installed.

Also attached a picture of the decal before install.

they consist of three layers of media.

2 layers of laminate and then laminted to the brushed chrome vinyl

and contour cut.

I will be shipping your dash back soon Sarge.

Thank You

[Duff 206]

DARN, does that look GOOD!!!!

Duff :D

[bell 11]

I need one of these.... When will they be available? Thanks, JB

[Vinylguy 4,687]

I will be listing them on my website soon.

I will have a dozen ready next week.

Make sure you have a clean smooth well prepped dash before installing.

any little particles can sneek in under the decal and will show up.

[bell 11]

:banana: I'll be ordering the decals for my 1045 then! :banana:

Beautiful work, by the way! :hide:

[Brian1045 28]

Hoorah!!...I'll be watching the website for sure! :hide:

[saguaro 0]

I like that. Thats sharp :hide:

[Vinylguy 4,687]

here is a link to the dash decals

http://www.redoyourhorse.com/servlet/the-7...ALUMINUM/Detail

[saguaro 0]

Do you do the same process with the Ranger decals.

[Vinylguy 4,687]

I am going to run some soon and will post results

Thanks

[Sarge 3,464]

Actually, the dash I sent you is off the 876 ....

Both the 1277 and 876 are Wheel a Matic auto's with Sundstrand hydro's .

My bad, should have sent the pic first , but if nothing else you have the finished product done for the manual trans units built at the same time/era .

Looks sharp, anyway .

Sarge

[Sarge 3,464]

Here's what it looked like when removed/blasted partially . Strange how they spaced out the "Wheel a Matic" lettering , and the font used .

My Webpage

Sarge

[Sarge 3,464]

I got a few pics from Perry since his 1277 is in original condition and still looks pretty good - at least his is legible !

Amazing how good his look , and how bad both of mine are rusted . Took a lot of primer and wet sanding to fill that plate in well enough to prevent show-through on the vinyl . Can't wait to see Terry's finished product !

Sarge

[bell 11]

TD, are these still available? I went to figure out what I'm going to order.... and they are GONE! :hide:

[Vinylguy 4,687]

I have them just have not gotten them listed for the wheel a matic yet

I am making the wheel a matic bottoms in black and white and the top brushed aluminum ones are all the same. Sarge forgot to tell me his were wheel a matics so I am removing them from his dash panel and reapplying the wheel a matic decals

Will list them soon and send a link

TD

[Kelly 1,030]

Terry I see someone is selling what looks like your decals on ebay right now, are they yours??? http://cgi.ebay.com/WHEEL-HORSE-DASH-DECAL...1QQcmdZViewItem

[Vinylguy 4,687]

A very nice young lady in our town with two small kids started an ebay business and buys some of our decals and is hoping to make a few bucks reselling them on ebay.

only thing is she will be listing old baby clothes along side. LOL

[Sarge 3,464]

:hide: Like I said - my bad :imstupid:

Funny how some folks try to make money , lol .

Can't wait to see the dash , Terry you sure did this one proud !

Sarge

[Kelly 1,030]

If it's ok with you, I wouldn't mind helping her out, and may buy from her right now, maybe she could use a few bucks before christmas :hide:

[Vinylguy 4,687]

No problem Kelly.

works for me

TD

[HorseFixer 2,012]

Looks good Terry as allways you do a fine job! :hide:

[Sarge 3,464]

Ok, just got the pics of the new wheel-a-matic decal from Terry today -

Can't wait to put it together ...

Sarge

[perry 82]

nice! :hide:

[Kelly 1,030]

I have both sets of the dash decals now, I can't wait to get them put on the panels the decals look top notch :hide:

[Groffster 0]

How do i get those decals i need them and others for my restoration????