Jump to content
Horsing Around RS

Need some help with a C-160

By Horsing Around RS, in Wheel Horse Tractors

Recommended Posts

Horsing Around RS    27

Horsing Around RS
Posted

Ok guys I'm stumped. I have a 1975 C-160 and I have a couple problems with it.
1. There is a voltage draw on it some where, even when the key is off. - not a huge problem
2. After the tractor has been running awhile, it turns itself off and cannot be restarted again until it has cooled down. The starter will not even engage. I have replaced the coil and condenser. It has a new battery too.
The system is charging. I asssume it needs a new starter because once it gets warm it no longer works. But I do not know why it would turn itself off.

I am not sure if these 2 issues are related but any help would be greatly appreciated.

Share this post

Link to post
Share on other sites
 

chip61    658

chip61
Posted

Not sure why it would shut down-I had a tractor that would run great for anywhere from 20 minutes to several hours then shut down. It turned out to be trash in the fuel tank. As far as not turning over, have you checked for current at the solenoid when you turn the key to start?? Also, do you have current at the coil when it shuts down??

Share this post

Link to post
Share on other sites
 

squonk    41,010

squonk
Posted

Check the ammeter and connections.

Share this post

Link to post
Share on other sites
 

pacer    3,168

pacer
Posted

Find a way turn the engine over by hand - figure this out before it gets hot - Have a socket/ratchet with you to try and turn the flywheel when it stops. Could possibly be "seizing" caused by overheating (clogged cooling fins, bad/old/low oil, etc) If you can turn the motor by hand right after it stops then continue on chasing something else. If unable to turn over until cooled then you have got some serious problems, once an engine seizes it scores the piston, collapses the rings and possibly mars the cylinder wall.

Share this post

Link to post
Share on other sites
 

Horsing Around RS    27

Horsing Around RS
Posted

Pacer: Engine does turn over by hand after it stops running. Thanks
Squonk: I will check the amp meter. I guess that could be a draw. Thanks
Chip61: The fuel is clean. Thanks

Thanks for trying to help guys.

Share this post

Link to post
Share on other sites
 

chip61    658

chip61
Posted

Is the coil polarity correct??

Share this post

Link to post
Share on other sites
 

squonk    41,010

squonk
Posted

Everything electrical goes thru that ammeter. I have seen the connections the melted, burnt, corroded ect. Things get hot and break apart.

  • Like 1

Share this post

Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Go To Topic Listing

  • Similar Content

    • davidfindlay
      1984 C Series, dump trailer and leaf impeller
      By davidfindlay
      Looking to find a new home for my 84 (I think) C-145. It has a dump trailer with the enclosure for leaves, the PTO impeller to get the leafs into the trailer, the hoses for deck-to-impeller, impeller-to-trailer.
       
      I haven’t run it in over a year.
      The battery and the cable to the battery probably need to be replaced.
      Comes with a new head gasket still in the bag.
      Seat is cracked but still comfortable.
       
      Happy to answer questions or take other pictures.















    • 87 416-8 horse
      Wanted wheel horses
      By 87 416-8 horse
      I’m looking for wheel horse tractors for sale or for parts in the Eastern Nebraska or western Iowa area. Preferably 8 speed manuals. Pm me or comment with what you have. The worst I could say is it’s out of my price or distance range. Edit: engine is not important, it’s going to get an engine swap.
      Thanks,
      John
    • BrianStasC-101
      predator 420 pto
      By BrianStasC-101
      Hello all. I am looking for suggestions on adapting the pto from my C series tractor to a harbor freight predator 420 13hp engine. I know the predator motors are a controversial topic however it is the route I have chosen for this particular machine. The intent was to mostly use it for plowing so no PTO required but it would be handy to have. Looking to hear from someone that has successfully done the swap that may offer any advice before I attempt to transfer it over. Just looking for any general pointers that will help me along the way to make it go as smoothly as possible. 
    • HumbleHans
      Tractor 1984 C -Series OM Wiring Rev.pdf
      By HumbleHans
      Operator manual 810343R1
      Wiring
      34 pages 17.5MB
       
      Wiring Colored 
      1 page 228KB
       
      1984 C-105 8-Speed model 11-10K802
      1984 C-125 8-Speed model 11-12K802
      1984 C-145 Automatic model 11-14KE01 - Some used alternate inner axle bearing See PSB #369
      1984 C-165 8-Speed model 11-16K801
      1984 C-175 Twin Automatic model 11-17KE01 - Some used alternate inner axle bearing See PSB #369
      1984 C-195 Twin Automatic model 01-19KE02
       
       
    • t_furl43
      1979 C-101
      By t_furl43
      1979 c-101 nice project tractor just needs a few odds and ends, steering wheel, coil, carburetor bowl, the wiring was redone by previous owner....all 4 tires are good and hold air it goes into all gears no problem, transmission fluid has been changed, 10hp Kohler, message me or call or txt with any questions, it does run and runs well,  it’s been kept inside since I’ve had it, I would also trade for a mid mount grader blade thanks 




      92DB561C-FF95-4868-A52B-5725D4D3B9DE.mp4
×
×
  • Create New...