Jump to content
jm46322

rustoleum appliance expoy questions

By jm46322, in Restorations, Modifications, & Customizations

Recommended Posts

jm46322    32

jm46322
Posted

Just got done sand blasting a set of rims. when I was  starting to prime them and said wait I will check and see if I am using the correct primer.

pulled up the technical data sheet for the stuff on line and it states that "priming is not recommended"

it talks about removing loose paint  and rust  with wire brush / sand paper and removing gloss with sand paper.

mainly it addresses top coating a already painted surface.

I am 99.9% bare metal  so do I still not prime?

I seen a lot of talk of this prime on here

have you guys primed or put it on straight out of the blaster?

 

thanks

 

Share this post

Link to post
Share on other sites
 

slammer302    2,155

slammer302
Posted

I did a 657 deck I didn't use primer

I also noticed its not recommended for use out doors in sunlight

Share this post

Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Go To Topic Listing

  • Similar Content

    • PWL216
      Aftermarket Front Rims for C Series
      By PWL216
      Are there aftermarket front rims available for C Series tractors? I have a 120 and a 160 that need front rims… thx.
    • r1jakecfd
      Rim dimensions for 24x12-12 rear tires- 520H
      By r1jakecfd
      Hi Guys,
      I just bought some Carlisle Turfmaster 24x12-12 rear tires to replace the 23x8.50-12 tires I have on there now. I was wondering which rims I should buy to fit these bigger tires. The charts say an 8.50 width rim but should the offset stay the same or does it need to change? Any other dimensions I should be concerned about?
      Thanks in advance.
      Hope everyone is healthy and well!
      John
    • 1990520H
      520H swept axle rims
      By 1990520H
      What is a good replacement rim for the fronts since you can no longer get the stuff from Toro. Been looking. Not much luck. Any help would be greatly appreciated.
    • old5foot
      89' 312-8 Rear Rim Paint color
      By old5foot
      I have an 1989 312-8. The Owner's Manual shows a color photo/picture of a WH with silver/gray rims. The WH has silver/gray rims now, but it definitely is not the original paint. I am redoing the rims (sandblast and repaint) and I would like to repaint with as original a color as possible. I would appreciate any information available. Thanks Old5foot
    • old5foot
      Tires & Rims on a 312-8, Kenda Terra 502
      By old5foot
      Anybody had any success mounting Kenda Terra 502 tires on 7.5 x 12 Wheel Horse rims?
      Kenda says the tire needs a 8.5 x 12 rim. They spec. out as 23 x 10.5 x 12.
      My 318 rims measure 7.5" from inside of bead to inside of bead. So they just might work.
      Reason for all this being I have some steep slopes down to the lake.  Yard has a toboggan run slope, a couple of  8 - 10 foot drops with flat areas in between.
      Total drop of about 20 feet in about 100 feet. Plus the soil is Michigan sand.  Grass is thin and the old original Carlisles just aren't cutting it anymore.  
      Looking for a more agressive tire for turf.  Have read some goon reviews of the 502's on this forum.  But not much detail on the rims they were mounted on.
      Any experiences good or bad would be appreciated.
      Thanks
      Old 5 Foot
×
×
  • Create New...