Jump to content
km3h

Wheel Horse Hour Meter

By km3h, in Wheel Horse Electrical

Recommended Posts

km3h    543

km3h
Posted

Removed rear fender and hood for cleaning on my newly free 416H. I noticed that the hours meter worked but the black face inside the meter turned as the seconds passed by. When I examined the meter I found that the ring holding the glass which acts as the front mount loose on one side. Can't figure a fix for this.

I can replace the meter with a new on but that will start at zero and if I ever decide to sell this will make me look like I am trying to scam someone. This tractor only has 520 hours on it. Any solutions as to how to fix the meter.

Share this post

Link to post
Share on other sites
 

Fordiesel69    263

Fordiesel69
Posted

Replace, and leave key on until 520 hrs are reached.  Haha.....

Share this post

Link to post
Share on other sites
 

meadowfield    2,594

meadowfield
Posted

Replace, and leave key on until 520 hrs are reached.  Haha.....

That is the sensible way :D

Share this post

Link to post
Share on other sites
 

km3h    543

km3h
Posted

I have already thought of that. Now the good news is that I was able to locate a complete replacement plate with both meters in good condition. Meter only has about 250 hrs. Put it on a power supply for 10 days and my problem is solved. 

Share this post

Link to post
Share on other sites
 

Save Old Iron    1,566

Save Old Iron
Posted

. Put it on a power supply for 10 days and my problem is solved. 

+1 on the power supply

 

the key on method will not work if the hour meter is powered off an oil pressure switch

Share this post

Link to post
Share on other sites
 

km3h    543

km3h
Posted

Have a 12 volt power supply.

Share this post

Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Go To Topic Listing

  • Similar Content

    • ztnoo
      The First Instances Of Factory Installed Hour Meter On Wheel Horse Tractors
      By ztnoo
      Can anyone tell me when (the year), and what models hour meters began to be factory installed on Wheel Horse tractors?
      At what point did they become standard on all Wheel Horse models?
    • mikekot3
      Wheel Horse 416-8
      By mikekot3
      Hello
      I want to buy the seat mentioned in Martin Howard's 416 adventures. I tried to contact him but he is not able to receive emails through red square.
      I have a 1993 WH 416-8 tractor. He used a KM UNIPRO 123 seat from www.turfseats.com
       Which seat switch do I use on the replacement seat? My used my FLUKE 88 dvom in auto ranging mode to test the original seat switch. With the
      seat switch disconnected I get a ohm reading and O.L when I sit on the seat. I am thinking that tells me
      that the seat is Normally OPEN.  Am I correct in this? Did the KM seat switch come with a pigtail for wire it up?
      If not how do I install the switch? Where did you get the seat rubber bumpers for the swing up seat base? I believe they were black or grey.
      Also I installed a Briggs and Stratton Vanguard v-twin 23 hp engine swap kit from small engine warehouse.
       
      The hour meter does not work any more after replacing the swapped in engine. I was thinking that a aftermarket hour meter/tach from esitest.com would
      work. http://esitest.com/329.html
       
      My other question is that I can only start the tractor by turning the key and also turning the light switch ON to engage
      the starter motor.  I am thinking one of the power wires in the white AMP engine harness connector is in the wrong pin position as I had to
      replace the connector.
       
      Please advise,
      Michael Kotarba
      mkotarba@hotmail.com
×
×
  • Create New...