Jump to content

 
Countdown To Christmas!
 

 
Sign in to follow this  
Followers 0
WoodMotorsports

Gasket identification needed. (C-160 Auto)

By WoodMotorsports, in Transmissions and transaxles

Recommended Posts

WoodMotorsports    3

WoodMotorsports
Posted

I'm having a bit of a time trying to ID a gasket through the Toro parts viewer. What is the large aluminum housing on the hydrostat/transaxle called in the picture below?

110d9cda.jpg

You can see the corner of the gasket in my fingers, and it leaks pretty badly from the same spot.

Share this post

Link to post
Share on other sites
 

smoreau    658

smoreau
Posted

I think thats part of the drive motor. As for gaskets. try your toro dealer for some more info. Also some one here that knows more will most likely chime in and help

Share this post

Link to post
Share on other sites
 

pfrederi    17,886

pfrederi
Posted

Gasket is 83-3760 still available for about $9.00 Really is a simple gasket if you choose to make it yourself. You will need a snap ring pliers to remove the cover.

After looking inside several Sundstrands I can tell you do not repeat not use silicone for a gasket

Share this post

Link to post
Share on other sites
 

WoodMotorsports    3

WoodMotorsports
Posted

Now that's fast service! Thanks gentlemen.

Share this post

Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  
Followers 0
Go To Topic Listing
  • Similar Content
     
     
    • davidfindlay
      1984 C Series, dump trailer and leaf impeller
      By davidfindlay
      Looking to find a new home for my 84 (I think) C-145. It has a dump trailer with the enclosure for leaves, the PTO impeller to get the leafs into the trailer, the hoses for deck-to-impeller, impeller-to-trailer.
       
      I haven’t run it in over a year.
      The battery and the cable to the battery probably need to be replaced.
      Comes with a new head gasket still in the bag.
      Seat is cracked but still comfortable.
       
      Happy to answer questions or take other pictures.















    • 87 416-8 horse
      Wanted wheel horses
      By 87 416-8 horse
      I’m looking for wheel horse tractors for sale or for parts in the Eastern Nebraska or western Iowa area. Preferably 8 speed manuals. Pm me or comment with what you have. The worst I could say is it’s out of my price or distance range. Edit: engine is not important, it’s going to get an engine swap.
      Thanks,
      John
    • BrianStasC-101
      predator 420 pto
      By BrianStasC-101
      Hello all. I am looking for suggestions on adapting the pto from my C series tractor to a harbor freight predator 420 13hp engine. I know the predator motors are a controversial topic however it is the route I have chosen for this particular machine. The intent was to mostly use it for plowing so no PTO required but it would be handy to have. Looking to hear from someone that has successfully done the swap that may offer any advice before I attempt to transfer it over. Just looking for any general pointers that will help me along the way to make it go as smoothly as possible. 
    • HumbleHans
      Tractor 1984 C -Series OM Wiring Rev.pdf
      By HumbleHans
      Operator manual 810343R1
      Wiring
      34 pages 17.5MB
       
      Wiring Colored 
      1 page 228KB
       
      1984 C-105 8-Speed model 11-10K802
      1984 C-125 8-Speed model 11-12K802
      1984 C-145 Automatic model 11-14KE01 - Some used alternate inner axle bearing See PSB #369
      1984 C-165 8-Speed model 11-16K801
      1984 C-175 Twin Automatic model 11-17KE01 - Some used alternate inner axle bearing See PSB #369
      1984 C-195 Twin Automatic model 01-19KE02
       
       
    • t_furl43
      1979 C-101
      By t_furl43
      1979 c-101 nice project tractor just needs a few odds and ends, steering wheel, coil, carburetor bowl, the wiring was redone by previous owner....all 4 tires are good and hold air it goes into all gears no problem, transmission fluid has been changed, 10hp Kohler, message me or call or txt with any questions, it does run and runs well,  it’s been kept inside since I’ve had it, I would also trade for a mid mount grader blade thanks 




      92DB561C-FF95-4868-A52B-5725D4D3B9DE.mp4
    		 
×
  • Create New...