Jump to content
Sign in to follow this  
coldone

D200 Pressure test vid.

Recommended Posts

coldone

Here is the vid of me performing a preesure test on the D200. I had mowed the entire yard with it earlier today then parked it for a few hours. The engine was still warm to the touch but the hard lines were ambient temp.

[media=]

  • Like 2

Share this post


Link to post
Share on other sites
 
pfrederi

Nice Video. You did a great job!

The alternative pressure hook up is an #6 ORB (O ring boss). It is on the top of the pump. I would like to permanently mount a pressure gauge but i haven't figured out how to plumb it and have room for the battery.

Share this post


Link to post
Share on other sites
 
Trouty56

Good video....just one thing though.....did you say "back to the steaks"...?? Those steaks would have been too well done for me already...lol... All jokes aside...great job all round. By the way...I'm a big fan of surplus center.

Share this post


Link to post
Share on other sites
 
JamesBe1

Excellent vid. Thanx for posting that.

You might not want to trust the accuracy of the mechanical pressure gage below 10% of range. It's more for qualitative purposes than quantitative. But at least it's showing that you have pressure when you should have pressure. Also, one heck of a great job on the motor rebuild. I enjoyed the pics. I might not be so squeamish about opening one up next time.

I have been pondering adding a hydro pressure gage in the dash where the hours meters goes. Not sure if I can even find a 2' recessed pressure gage though. Still, I don't think I would want to run a 1k PSI pressure line up there if I don't have to. I would want to find a way to use an electrical sensor and gage instead.

But the most important thing was the steaks! I hope you enjoyed!

Share this post


Link to post
Share on other sites
 
coldone

Good video....just one thing though.....did you say "back to the steaks"...?? Those steaks would have been too well done for me already...lol...

Yes I said steaks and yes they were too done but I promised yall a video. They were still juicy just a little too well done no pink in the middle. :D

  • Like 1

Share this post


Link to post
Share on other sites
 
JackC

Thanks for the video.

Share this post


Link to post
Share on other sites
 
1maidenfan

Good video....just one thing though.....did you say "back to the steaks"...?? Those steaks would have been too well done for me already...lol...

Yes I said steaks and yes they were too done but I promised yall a video. They were still juicy just a little too well done no pink in the middle. :D

Gotta like the "pink in the middle" :ychain:

Excellent video. :bow-blue:

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Similar Content

    • BuffaloD200
      By BuffaloD200
      '74 D-180
       
      My friction disc in gone on my clutch.  I saw the old post about making a new friction disc, so I'm not concerned about that.
      I managed to remove the front clutch plate and double v-belt pulley.  But I can't separate the two.  When I took the assembly off the spiraloc washer popped off on its own.  I HAVE READ THE MANUALS.
      So I should be able to just remove the pulley from the front clutch and continue with step 4.  The v-belt pulley is loose as all hell and flops around like a dead fish.  It seems to be hung up on a ring or bearing race.  
      So my thoughts are grab a BFH or sparky the blue tip wrench.
      Is there an unpublished step 3.5, or some trick?
    • BuffaloD200
      By BuffaloD200
      Hey all, 
       
      My '74 D180 has a lot of trouble pushing snow.  Weighted tires, but nothing else at this time.  I've found it gets stuck frequently and only one wheel spins.  Do these tractors not have a limited slip/locker arrangement?  How does everyone manage with the infamous one wheel peel?
    • BuffaloD200
      By BuffaloD200
      Hey all, I need to install a drive belt on my 75 D180 for my snowblower.  I've looked through a bunch of D-series owner's manuals, and none seem to mention replacement procedure.  The PTO pulley is fixed, save for engaging the PTO and there is minimal movement at the snowthrower pulley. There's no idler or tensioner as far as I can tell.  Do I have to remove the PTO pulley?  That seems to be a required service item.
      Same question for my 80 D200 as well really.  
       
      Using the recommended 4L490W belt.
       
      Thanks 
    • ihatephones
      By ihatephones
      I got a D-180 for $250, and the governor is messed up, the points won't open or close, and I took it apart and was being stupid and messed some stuff up in there, and now I need a new one.
      Where can I get one that's not on eBay for $200?
      I also forgot to say it was a Kohler K482, and I'll throw some pictures of the tractor in as a treat.


    • giant_g2
      By giant_g2
      Not sure on specific model. This 8 spd came attached to a plow I bought. It had some water in it for a couple weeks according to the prior owner. I drained it, sloshed some diesel in it, drained that, then filled with fresh oil. Spinning the input shaft by hand, I can see the axels turn. Hasn't leaked any oil. I'm not really interested in shipping, so I'd prefer local sales.

×
×
  • Create New...