Jump to content
Sign in to follow this  
rmaynard

Another frustrated soul with non-removable hubs

Recommended Posts

rmaynard

I'm trying to remove 1-1/8" hubs. I read all the posts so that I would do it right. I have soaked them with PB Blaster, heated, tapped, tightened puller, over and over again until I feel that one more attempt at tightening the puller will either strip the threads or break something.

I have been at this since early this morning. :omg::D

I'm using this type of puller.

65289e58.gif

Any additional ideas or just moral support from someone who has been there would be appreciated.

Bob

Share this post


Link to post
Share on other sites
 
CasualObserver

Bob, if you have steel and a welder, or an extra hub laying about I would suggest trying the ideas in these threads over that jaw puller.

Share this post


Link to post
Share on other sites
 
rmaynard

Bob, if you have steel and a welder, or an extra hub laying about I would suggest trying the ideas in these threads over that jaw puller.

http://www.wheelhorseforum.com/index.php?showtopic=206

http://www.wheelhorseforum.com/index.php?showtopic=12731

Unfortunately, no welder. However, I know that I am applying well over 200 ft/lbs of torque on the puller and I have not gotten even 1000th of an inch movement. I know because I am standing on the wrench with one foot, and I'm 200 lbs. :omg:

If it would just start to move a little, I would be happy.

Bob

Share this post


Link to post
Share on other sites
 
Save Old Iron

If it would just start to move a little, I would be happy.

Sounds like the thoughts going thru my wife's head when she sees me napping on the couch when there's stuff to be done !

and now for the encouragement part - Go Bob Go !!

Keep whacking that little rusty shaft - the hubs will come off eventually

op51-23001text.jpg

Share this post


Link to post
Share on other sites
 
rmaynard

rmaynard,March 19, 2010 04:34 pm] If it would just start to move a little, I would be happy.

Sounds like the thoughts going thru my wife's head when she sees me napping on the couch when there's stuff to be done !

and now for the encouragement part - Go Bob Go !!

Keep whacking that little rusty shaft - the hubs will come off eventually

Thanks Chuck, but I am giving up on the claw puller and I am going to make one from an old 1" hub as did Paul (pfrederi Post Number 99674).

I like the idea of giving the old one-incher a whack or two.

Bob

Share this post


Link to post
Share on other sites
 
rickv1957

I like the idea of giving the old one-incher a whack or two.

Go Bob Go!! :omg: Rick

Share this post


Link to post
Share on other sites
 
Save Old Iron

I like the idea of giving the old one-incher a whack or two.

Go Bob Go!! :omg: Rick

I'm should charging you guys entertainment tax on my posts

Share this post


Link to post
Share on other sites
 
tommy3horse

Forget about the hub....think about the cheerleaders!! :omg:

Tom

Share this post


Link to post
Share on other sites
 
Lane Ranger

Bob that second hub thing Paul suggested worked absolutely great in removing my B-80 HUBS for the changing of the oil seals .

I recommend it but you really have to have some good carriage bolts and you have to be extra careful not to ding the threads on the hubs.

I used an extra heavy duty bolt on the inside of the HUB for placing on the axle. Even the heat torch does not always work well but I found this method to work.

Good luck.

:omg:

Share this post


Link to post
Share on other sites
 
Butch

I'm trying to remove 1-1/8" hubs. I read all the posts so that I would do it right. I have soaked them with PB Blaster, heated, tapped, tightened puller, over and over again until I feel that one more attempt at tightening the puller will either strip the threads or break something.

I have been at this since early this morning. :omg::D

I'm using this type of puller.

65289e58.gif

Any additional ideas or just moral support from someone who has been there would be appreciated.

Bob

I sure know the feeling about wondering how far you can push a puller to it's limits! I've hidden behind things and have used a 4 foot breaker bar to slowly apply more torque! :D I've even used my impact wrench with a socket and 16 extensions on it to turn the puller! Nope. Don't like pushing the envelope on those things and I don't wanna be a statistic. :D

Share this post


Link to post
Share on other sites
 
MaineDad

Pullers, heat, PB Blaster and a big rubber mallet. I've broke them on purpose just to show 'em who's boss :omg:

Share this post


Link to post
Share on other sites
 
btrrg1969

I have never tried to pull one off , however I was just wondering , if you could get to the back side , the thickest part of the hub with a air chisel as you keep pressure on your puller and then rotate it as you work ? :omg:

Share this post


Link to post
Share on other sites
 
rmaynard

Hitting from the backside will sometimes cause the entire axle to pull out of the case.

Bob

Share this post


Link to post
Share on other sites
 
stevebo

Beem there and done that-broken hubs and pulling the axle out of the clips sucks. I would try a little longer then have a shop press them off.

Share this post


Link to post
Share on other sites
 
rmaynard

:D :D

Kudos to Paul (pfrederi) for his hub puller design. I went out and bought everything I needed for about $10.00 and made my own puller.

ce446861.jpg

One hour later, blisters in my palm, one can of PB Blaster and half a tank of MAP gas used, not to mention a very large hammer to beat on the 1" bolt head, success!

ef40ed47.jpg

Okay, so I got them off.

Now, how do I get them back on? :omg:

Bob

Share this post


Link to post
Share on other sites
 
tarcoleo

Bob-

I'm not envious of your problem, but it surely is a challenge.

Can't help but think that equal portions of patience, continued

pressure from the puller, PB Blaster, HEAT, and a few well placed

taps with a hammer cushioned by a hardwood block--should get

the damn thing off.

Good luck, Tom in RI

Share this post


Link to post
Share on other sites
 
rmaynard

It took me five hours over over two days to remove two hubs. Not an easy job, and very frustrating to say the least. :D

Yet I am left wondering why some tractors have a problem with hubs drifting or moving on the axle.

Here is an example: LINK

How can my hubs (on two separate transmissions) be so cotton-pickin' hard to get off, yet others fall off or drift inward in the course of normal operation? :omg:

Bob

Share this post


Link to post
Share on other sites
 
Roger from southern Iowa

Remove the axle key and remove rust from inside hub and the axle apply some light oil.

Reinstall key and they have always slid right on for me.

Clean, clean and more clean. :omg:

Share this post


Link to post
Share on other sites
 
Ole MN

Emery cloth and oil, shine up the shaft and hub slide it on.

Share this post


Link to post
Share on other sites
 
MikesRJ

Neversieze works wonders too.

Share this post


Link to post
Share on other sites
 
rmaynard

Remove the axle key and remove rust from inside hub and the axle apply some light oil.

Reinstall key and they have always slid right on for me.

Clean, clean and more clean. :omg:

Thanks Roger.

To others out there, has anyone ever tried an anti-seize product such as Dynatex on the axles?

Dynatex Anti-Seize

Bob

Share this post


Link to post
Share on other sites
 
Roger from southern Iowa

Am I one of the others? :omg:

I've never used that brand, but anti-seize in general sure helps if you have to do the same job in the future. :D

Share this post


Link to post
Share on other sites
 
pfrederi

I use permatex never-seize on everything. it is messy and gets all over you and everything you touch. BUT I have removed exhaust manifold bolts that I put on with never seize 10+ years ago with no problem..

Share this post


Link to post
Share on other sites
 
rmaynard

I use permatex never-seize on everything. it is messy and gets all over you and everything you touch. BUT I have removed exhaust manifold bolts that I put on with never seize 10+ years ago with no problem..

Thanks Paul, and many, many thanks for the puller concept you came up with. It was slow, but effective. Only thing I need to find is 3/8" grade 8 bolts with all-thread. My local TSC sells grade 8, but no all-thread.

Bob

Share this post


Link to post
Share on other sites
 
HorseFixer

Good Job Bob! :D and Chuck I think it was the Cheerleaders that did it! :omg:

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×
×
  • Create New...