My first puller

[Crazywheelhorseman 67]

All i have to say is it looks great Chris can't wait to see it when it is done. think it will be ready for the spring meet and greet? :WRS:

[TT-(Moderator) 1,131]

:thumbs: I applaud your efforts, Sir!

I do see the fuse on the Briggs bomb growing much shorter though. :banghead:

[Stress Test Pullin 0]

well over it looks good, im curious to see it run :thumbs:

[chris11 184]

I applaud your efforts, Sir!

I do see the fuse on the Briggs bomb growing much shorter though.

Terry you dont think it can be done? I have built alot of open briggs engines for karts. wont take much to machine rods. put inserts in. will have to crate the block.

[Crazywheelhorseman 67]

Chris, did you find out if that was a pressurized system or a splash?

[chris11 184]

Its splash, love to have a vanguard on it.but ill work with what i have.

[Stress Test Pullin 0]

your best bet for pulling would be to buy a Kohler 25 hp vtwin, and modifying it

[chris11 184]

yes that would be nice , but ill stay with my plan, best part of what i do for a living is i can run it on my shops dyno to dial it in. takes the guess work of of every thing.

http://www.ktrmotorsports.com/service/dynamometer.htm

[TT-(Moderator) 1,131]

Terry you dont think it can be done?

Oh - It can definitely be done - I just don't see it lasting long in modified form.

[rickv1957 72]

Chris,very nice work there! Rick

[bitten 134]

Looking good, I like what you did with the front end and spindles.

[jusjeepn 59]

A-W-E-S-O-M-E job Chris! :thumbs:

[chris11 184]

Just made a deal with a guy for a Kohler 25 hp vtwin. so ill keep the briggs for something like a big weed wacker :thumbs:

[baerpath 517]

your best bet for pulling would be to buy a Kohler 25 hp vtwin, and modifying it

:thumbs:

[marvairplanes 34]

Cool Stuff !!!

Marv

[Michael Bullington 5]

Nice work...awesome!!

[chris11 184]

I got my 25 Horse command Kohler today, looks like it will fit the frame well. Now to start doing some mods to it. :thumbs:

[baerpath 517]

I know ya got the command but for future referance

http://www.performancevtwins.com

Duane

[chris11 184]

Thank you Duane. :thumbs:

[chevy030303 0]

ok where did u git the frame parts and frout tires and wheels ??? :party:

[clintonnut 126]

If you haven't noticed already, wheel horse frames are made of parts you can aquire at your local hardware store.

Charlie

[chris11 184]

I had a 8 foot piece of 2 by2 angle iron the same as wheelhorse used. The back mount is from a old frame that was cracked. I cut it off and cleaned it up. 3/4 round stock is DOM tubing thick wall. and i made the front pivot mounts for the front axle. made a new pivot pin,steering shafts. Thats the frame parts. The front axle i machined the pivot hole out and made a bronz bushing on a 10 degre angle. because the frame has a 7 degre rake.also made up some lowered spindles. axle should have about 3 degree caster. wheels from midwest super cub, tires from ebay. i have been very busy trying to get all the bits to build this kohler vtwin. so i can have this done soon. ill post pictures soon. B)

[chevy030303 0]

ok thanks B)

[josh416 2]

Im building that twin briggs to take both those carbs. Im building as a puller. but more for fun. i have the new rear ags just got to order rear rims. Paint is going to be base coat clear coat. 62 ferrrari red. i have spare engine to mods too. Thank you Mike

i have a onan 18 horse that i got twin carbs on and they were a pain 2 adjust but if ya get em right the engine runs so much more powerful B)

[chris11 184]

Well here are some new pictures of what is done. The 25 hp kohler is being built. i just made a manifol for the carb. and still have to make the top of the hood.