Snow Blower - Turn Handle Rod - Crank support?

[Brockport Bill 1,822]

Came across this tube in a misc parts pile -- it's part number # 119030 per a PartsTree sticker label on it -- it's identified as a "Crank support"  - apparently to hold a Snowblower crank rod handle -- however, the part number shows N/A and therefore I can't find a cross reference to what model blower it would go to?? It isn't the same angle design of a blower I would recognize ?? Any ideas what blower this would go to ? Thanks, Bill

[ebinmaine 70,668]

Does the flag fit in the end of that piece? 

[Pullstart 64,467]

The bottom lift arm is usually straight EB.  No bend in the middle.

[ebinmaine 70,668]

10 minutes ago, Pullstart said:

The bottom lift arm is usually straight EB.  No bend in the middle.

 

 

I had a single stage here for a little while that had a bend in the arm. Can't say for sure it was quite that steep.

@Maz91 has it now. 

 

 

 

[ebinmaine 70,668]

Wondering if maybe this piece is the one that stands up off the side of the frame on a two-stage?

[wallfish 17,484]

2 stage blower. There is a short solid rod on the blower frame in which that rod pins on to.

Edited December 11, 2024 by wallfish

[PWL216 940]

Hi @Brockport Bill here is a pic of that part and where it goes….

[gwest_ca-(File Mod) 11,241]

What model of tractor is that? Not our long frame model snowthrower.

 

[Brockport Bill 1,822]

1 hour ago, PWL216 said:

Hi @Brockport Bill here is a pic of that part and where it goes….

thanks - - what blower model name and number is that? I can't tell from that rear view??? Bill

[Brockport Bill 1,822]

6 hours ago, ebinmaine said:

Does the flag fit in the end of that piece? 

no flag does not go in that tube

[ebinmaine 70,668]

1 hour ago, gwest_ca said:

What model of tractor is that? Not our long frame model snowthrower.

 

 

41 minutes ago, Brockport Bill said:

thanks - - what blower model name and number is that? I can't tell from that rear view??? Bill

 

 

@PWL216

 

Is that the snow blower I now have?

[Brockport Bill 1,822]

6 hours ago, ebinmaine said:

 

 

 

@PWL216

 

Is that the snow blower I now have?

whatever the blower is in PWL216 photo that has the tube arm supporting the crank is what i am asking for the blower model description and # 

thanks

[Brockport Bill 1,822]

On 12/11/2024 at 9:25 AM, PWL216 said:

Hi @Brockport Bill here is a pic of that part and where it goes….

i came aross this FB post and the side angle photo appears to be a 2 stage wh blower with that tube crank support that looks like the one i have? Yes/no?

[ebinmaine 70,668]

2 hours ago, Brockport Bill said:

i came aross this FB post and the side angle photo appears to be a 2 stage wh blower with that tube crank support that looks like the one i have? Yes/no?

 

 

I'd say that's true. I have those parts at home. I can get you pictures and measurements sometime in the next couple days to confirm.

[Brockport Bill 1,822]

6 minutes ago, ebinmaine said:

 

 

I'd say that's true. I have those parts at home. I can get you pictures and measurements sometime in the next couple days to confirm.

excellent -- thanks

[Brockport Bill 1,822]

2 hours ago, ebinmaine said:

 

 

I'd say that's true. I have those parts at home. I can get you pictures and measurements sometime in the next couple days to confirm.

Eric -- witht the clues you and others provided,  i just found the info on that blower crank support tube - went to the Interchange list to research models of blowers --  then to the various diagrams on partstree - - so i won't need you to research  -- so THANKS FOR OFFER -- in fact, tube is for 2 stage blower models 06-44sc01 and successor model # 79361  -- it is the crank support tube. Appreciate your offer to research !!

 

as an fyi -- its N/A any longer. 

Bill