Help Needed 5 XI Two Stage Jack Shaft

[stevebo-(Moderator) 8,575]

I purchased a 2 stager 2004 5xi two stage blower. It is missing a few parts like jack shaft and chute angle rod. If you have a 5xi two stager could you please provide me with some pics and measurements so I can fabricate these parts? Obviously if you have these parts and want to sell please let me know as well. I have an ad in want section as well. Parts are showing as no longer available on line. 
Thank you!

[OoPEZoO 578]

I can get you measurements off mine later today

[Ed Kennell 42,823]

1 hour ago, OoPEZoO said:

I can get you measurements off mine later today

Didn't hear from you for awhile Keith.    Any update on Wally?

[OoPEZoO 578]

1 hour ago, Ed Kennell said:

Didn't hear from you for awhile Keith.    Any update on Wally?

Heat of the summer and kids soccer season took the wind out of my productive sails.  Enough so that there is still a wheel sitting in my electrolysis tank, but most of the water has evaporated. I need to get back on that.  I’d love to have him fixed up enough to bring him to the show next year, but that’s probably wishful thinking. 

[OoPEZoO 578]

@stevebo.......Hopefully this will help.  I just noticed you also asked for the tube crank support.  I'll go back out and get some dimensions of that as well.  If you need more pics or info, I'm glad to help where I can

 

Not to scale, but I believe I got all the important measurements in there

 

Jack shaft

 

Flag

 

 

Chute hand crank

 

 

 

 

 

 

 

 

 

[OoPEZoO 578]

Here is the guide pipe for the hand crank

 

You could be pretty sloppy with this and it would still work fine if you were making your own.

Its a 1" thin walled pipe with the last 2" crushed flat with a 9/16" hole drilled for the crank shaft to pass through.  The angle of the bend is 150 degrees, and the set screw at the bottom is 2" from the end of the pipe

[stevebo-(Moderator) 8,575]

Thank you so much! This will help me fab if I cannot find oem. 

[Gravely Horse 19]

I’m glad I saw this post. For the single stage blower, it apparently uses a flag with 3/4” rod instead of 1”. Are the dimensions of the flag the same aside from that? 

[Brockport Bill 2,031]

On 11/10/2024 at 9:08 PM, stevebo said:

Thank you so much! This will help me fab if I cannot find oem. 

if you have the Xi 2 stage blower and you think these pieces are what you need, please let me know?

do you need the "tube-crank support " -  I think might be piece # 95-3864-01???

plus, what they call the "yoke" looks like a flag? Maybe #94-7671-01 ??

 

see photo .................

[Oldschool 0]

On 12/13/2024 at 7:15 PM, Brockport Bill said:

if you have the Xi 2 stage blower and you think these pieces are what you need, please let me know?

do you need the "tube-crank support " -  I think might be piece # 95-3864-01???

plus, what they call the "yoke" looks like a flag? Maybe #94-7671-01 ??

 

see photo .................

 

[Oldschool 0]

Does anyone have these parts for sale? Looking for crank and crank tube.

 

Thank you.

[nylyon-(Admin) 8,215]

6 hours ago, Oldschool said:

Does anyone have these parts for sale? Looking for crank and crank tube.

 

Thank you.

Welcome to RedSquare, you should open a wanted ad in the classified section for the parts you are looking for.

[Gasaholic 333]

Dagnabbit.. about a year too late - last year I had a complete snowblower in used condition with everything , and couldn't sell it so tore it down and scrapped it - I'd have gladly sold you the whole shebang for a $100 bill - you'd have had tom come and get it but I still have a box of smaller useful parts and pieces along with the mule drive for it - I was going to de-grease em and list them on ebay , but shipping's so expensive these days I just never bothered. But if anyone's interested , I got a garage full of old used parts (wheel horse, farmall, and some unidentified flywheels and other "junked" parts I just havent cleaned out of the shop yet , but they're headed for dumpster or scrap pickup when I get around to it plus my 1948 farmall cub (with single bottom plow, sickle bar mower and disk harrow) for sale, if someone wanted to come by and pick through the shop and make offers on stuff , just give me a holler. Im way out in the boondocks, an hour from nearest interstates (I-99/US-15 or I-86) but right smack dab off of US-6... Oh yeah probably can dig through my old tool collections (So much stuff I've accumulated over the years and just never use it any more - even have an antique Growler for those who like old tools & stuff like that..)  I'm disabled, got  a bad back, so I wouldnt be much help with any lifting / loading