Starting an RJ Patina Special tractor

[Lane Ranger 10,943]

Yesterday I finally got around to putting on my  rebuilt RJ transmission (thanks Keith Jones and Larry Eads).  Put the rear wheels on this am. ( old Montgomery Wards ag tires with a different style tread) .  Began to work on motor tins, cull together missing parts ( clutch rod, lift cable, transmission boot, read hitch, etc.  amazed at the parts I have!) 

 

Here are some pictures of the first two days.

 

 

Yes that hood had some purple paint on it!  Sanding with three types of paper!  Going to finish up with Rustoleum Matte Clear as the final cover coat.  

 

 

 

 

 

[Lane Ranger 10,943]

One of the RJ tractors I bought several years ago had a great deal of original literature and paperwork 📋 about the sale etc.   what I have poster here is the cover for my original Master Catalina (probably 1958). A September 1, 1957 price list and an August 1, 1958 price for RJ tractor and all the dealers attachments, and tractor add ins! 
 

I think this is already on the Red Square site in publications etc but I thought I would post again for all you RJ Wheel Horse owners!

 

 

[WHX?? 48,749]

3 hours ago, Lane Ranger said:

old Montgomery Wards ag tires

I love those tires but old?? They look brand new minus the nubbies.

Tread pattern is almost the 6-12 version of these. 

 

I get a lot of complements on the plow field about their performance. 

Edited October 24 by WHX??

[Pullstart 62,757]

Lane I really have a thing for those tires, someday I’ll even own a set!  I almost bought a non-wheel horse tractor at Portage just for the tires, I should have done it and tried to flip it with another set!  

Edited October 24 by Pullstart

[WHX?? 48,749]

16 minutes ago, Pullstart said:

Lane I really have a thing for those tires, someday I’ll even own a set!

They would look & perform good on any round hood. 

[oliver2-44 9,674]

2 hours ago, Pullstart said:

I really have a thing for those tires

Only tractor guys would understand making a statement about "tires" in the same way we would talk about the good looking girl across the aisle back in our school days!

[Lane Ranger 10,943]

A little more work on the RJ Patina Specisl yesterday!   
 

closeup of the Wards Riverside for Pullstart!

 

 

The Kohler K 91 tins. - painted International Harvester Red.  I removed the drive pulley that was in this motor. With 3/4 shaft and I have an original to replace on it.

 

 

Unusual muffler in this Kohler K91 that I am going to keep.  I will thread the exhaust end and place 3/4 black pipe with a pepper pot muffler on the end! 
 

 

My patina fender pan looks good on the RJ patina Special and I have a good seat, left cable .  I placed a rear hitch on the transmission case yesterday also. 

Edited October 25 by Lane Ranger

[WHX?? 48,749]

20 hours ago, oliver2-44 said:

tires" in the same way we would talk about the good looking girl across the aisle back in our school days!

Ain't that the truth Jim! 

 

Looks like the muff is a stock one that someone closed off the outlets and welded a pipe on? Guessing the block is threaded behind it?

[squonk 41,016]

The engine I got from Cas for my Suburban originally had a bolt on muffler. Behind it was a 1/2" threaded hole. I had to use a 3/4" to 1/2" reducing street elbow. 

 

[Lane Ranger 10,943]

On 10/25/2024 at 9:57 AM, squonk said:

The engine I got from Cas for my Suburban originally had a bolt on muffler. Behind it was a 1/2" threaded hole. I had to use a 3/4" to 1/2" reducing street elbow. 

 

 

I had one with a flat muffler before and removed it and it was unthreaded.  I had to have it threaded at a machine shop near me.

 

 

Probably the better way to go!

 

 

[wallfish 16,980]

3 hours ago, Lane Ranger said:

I had one with a flat muffler before and removed it and it was unthreaded.  I had to have it threaded at a machine shop near me.

 

 

Probably the better way to go!

You don't need a machine shop to thread those exhaust ports, you need a NPT tap.

Tilt the engine over so the port is facing straight down and tap it up so the chips fall right out to the floor.

[Lane Ranger 10,943]

37 minutes ago, wallfish said:

You don't need a machine shop to thread those exhaust ports, you need a NPT tap.

Tilt the engine over so the port is facing straight down and tap it up so the chips fall right out to the floor.

 

yes I am not going to be lazy!  I figure when I take the muffler off it is not going to be threaded in the Kohler K91 exhaust port so why not!

 

 

 

[Lane Ranger 10,943]

Two small but important parts on a Wheel Horse RJ are the brake rod # 3545. ( # 90  in RJ manual drawing ) and the clutch spring anchor # 3585 (# 104 in the RJ manual drawing). 

[Lane Ranger 10,943]

Ok I took the flat  muffler off the Kohler K91 motor I am working on for my RJ Patina Special.   I broke the top bolt (snapped the nut) which as rusty as it was I figured one or both would snap.    But bottom one came off nice.  
 

 

Lo and behold the exhaust port appeared to be threaded! 
 

 

Like Wallfish and WHX indicated I will use an NPT tap and clean the threads better but I used my dremel tool to clean the threads and ran a short 3/4 pipe I had just to see if it was going to work it way in ok.

 

👍 looks like I am in business for an RJ exhaust pipe set up.

 

 

 

 

 

[wallfish 16,980]

22 minutes ago, Lane Ranger said:

Lo and behold the exhaust port appeared to be threaded! 

Nice! Yeah, many aren't threaded when you see those flat mufflers mounted.

I like to run the engines and get that port area hot when trying to remove exhaust bolts or even the head bolts near the exhaust. (If possible, but No need to worry in this instance since it's changing to a pipe).

Backyard hammer mechanic tip,  if you grind thin perpendicular lines into some scrap pipe threads on the pipe, it will clean out the engine threads better than just screwing a pipe in. Screw in, back off, keep repeating as necessary, then use the actual pipe piece you're going to use when you believe it's ready. Of course a real tap is best but sometimes it just needs a little cleaning out of the threads so the pipe trick works for that.