Jump to content
cJ_3D

PTO clutch support screw torque

Recommended Posts

cJ_3D

Hey all!

 

Replacing the drive belt on my 252-h. Anyone know the torque specification for the center screw when I put this pto clutch back on? I know it was on there tight it took a minute for the impact to break it loose. Thanks!

 

CJ

0623241528a.jpg

Share this post


Link to post
Share on other sites
 
WHX??

I would go to the torque limit that bolt can carry. Guessing 80-90 ft lbs but consult a chart. 

Share this post


Link to post
Share on other sites
 
cJ_3D
29 minutes ago, WHX?? said:

I would go to the torque limit that bolt can carry. Guessing 80-90 ft lbs but consult a chart. 

Hi WHX! Where can I find said chart? I've looked and can't find one. 

 

Thanks for the help!

Share this post


Link to post
Share on other sites
 
WHX??

Just :text-google: bolt torque chart. You'll find scads of them.

A good one will have all sizes, fine and coarse thread & most common grades... even metric. 

A must have in the shop for unspecified torque values. 

  • Like 1

Share this post


Link to post
Share on other sites
 
cJ_3D
3 minutes ago, WHX?? said:

Just :text-google: bolt torque chart. You'll find scads of them.

A good one will have all sizes, fine and coarse thread & most common grades... even metric. 

A must have in the shop for unspecified torque values. 

I'll give it a shot! Thank you!

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • bkarp@roadrunner.com
      By bkarp@roadrunner.com
      my magnum 12 kohler all of a sudden is blowing oil out of the carb. if rings are bad should oil be blowing out of the muffler.thanks for any help brent
    • razorback1995
      By razorback1995
      Hey all,
       
      This pully blew up on me yesterday. Having a hard time IDing the part # or replacements. the 308-8 schematics I've found don't list this part.  Its the pully in the front that runs from the motor to the mowing deck. 
       
      Thanks in advance!


    • Tinman1962
      By Tinman1962
      Recently got hold of a 656 it's has a "newer" 61/2 Briggs on it I don't believe that's right any ideas about that
    • Little Red Horse
      By Little Red Horse
      Hey all. I have a Electro 12 with a factory belly blade. It runs* and drives. I had used it to grade my driveway the last 6 yrs. Having moved I'm looking at my options on storing it or selling it. Frankly I have no idea what it is worth. I watched "ISaveTractors" video on 5 things to do with a new to you wheel horse/12hp kohler. (When i got it 6yrs ago) And went thru and did the adjustments and replaced the parts mentioned. It has been a good strong tractor for me until around July of this year. (2023)
      *Around July it started dying after running 20-30min. I replaced the carb (Chinese Amazon purchase) with one from isavetractors web site. That seemed to help it idle smoother(the old carbs jets wouldnt adjust), but it still dies at around 20-30min.
      So I've got 2 questions. 
      1. What is it worth? (As-Is) and
      2. What do I need to do to fix it? 
      Thanks yall!

    • 850ford
      By 850ford
      I am looking for a replacement Kohler for a 1980 c165,it is cradle mounted.
      Will a standard mount Kohler work, if I remove the cradle?
       I am located in Massachusetts 
        Thanks
×
×
  • Create New...