Jump to content
bkarp@roadrunner.com

oil problem

By bkarp@roadrunner.com, in Engines

Recommended Posts

bkarp@roadrunner.com    6

bkarp@roadrunner.com
Posted

my magnum 12 kohler all of a sudden is blowing oil out of the carb. if rings are bad should oil be blowing out of the muffler.thanks for any help brent

Share this post

Link to post
Share on other sites
 

moe1965    735

moe1965
Posted

Sounds like to much crankcase pressure. I would check the breather to make sure it's not clogged.    

  • Like 2

Share this post

Link to post
Share on other sites
 

RED-Z06    2,212

RED-Z06
Posted

How's the oil look..thin, smell of gas?

Share this post

Link to post
Share on other sites
 

Fordiesel69    259

Fordiesel69
Posted

coming thru the rubber vent hose by chance?

Share this post

Link to post
Share on other sites
 

Pullstart    62,637

Pullstart
Posted

:banana-gotpics: or video?

 

 

Share this post

Link to post
Share on other sites
 

bkarp@roadrunner.com    6

bkarp@roadrunner.com
Posted
23 hours ago, RED-Z06 said:

How's the oil look..thin, smell of gas?

no oil is normal,vent tube is open,spark plug is not fouled. i may had to much oil in engine,cleaned everything up  and cut grass yesterday and things seem ok,thanks for the input with the problem brent

 

 

Share this post

Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Go To Topic Listing

  • Similar Content

    • cJ_3D
      PTO clutch support screw torque
      By cJ_3D
      Hey all!
       
      Replacing the drive belt on my 252-h. Anyone know the torque specification for the center screw when I put this pto clutch back on? I know it was on there tight it took a minute for the impact to break it loose. Thanks!
       
      CJ

    • Tinman1962
      656
      By Tinman1962
      Recently got hold of a 656 it's has a "newer" 61/2 Briggs on it I don't believe that's right any ideas about that
    • Little Red Horse
      Wheel Horse Electro 12 Automatic
      By Little Red Horse
      Hey all. I have a Electro 12 with a factory belly blade. It runs* and drives. I had used it to grade my driveway the last 6 yrs. Having moved I'm looking at my options on storing it or selling it. Frankly I have no idea what it is worth. I watched "ISaveTractors" video on 5 things to do with a new to you wheel horse/12hp kohler. (When i got it 6yrs ago) And went thru and did the adjustments and replaced the parts mentioned. It has been a good strong tractor for me until around July of this year. (2023)
      *Around July it started dying after running 20-30min. I replaced the carb (Chinese Amazon purchase) with one from isavetractors web site. That seemed to help it idle smoother(the old carbs jets wouldnt adjust), but it still dies at around 20-30min.
      So I've got 2 questions. 
      1. What is it worth? (As-Is) and
      2. What do I need to do to fix it? 
      Thanks yall!

    • 850ford
      1980 C165
      By 850ford
      I am looking for a replacement Kohler for a 1980 c165,it is cradle mounted.
      Will a standard mount Kohler work, if I remove the cradle?
       I am located in Massachusetts 
        Thanks
    • BrianStasC-101
      predator 420 pto
      By BrianStasC-101
      Hello all. I am looking for suggestions on adapting the pto from my C series tractor to a harbor freight predator 420 13hp engine. I know the predator motors are a controversial topic however it is the route I have chosen for this particular machine. The intent was to mostly use it for plowing so no PTO required but it would be handy to have. Looking to hear from someone that has successfully done the swap that may offer any advice before I attempt to transfer it over. Just looking for any general pointers that will help me along the way to make it go as smoothly as possible. 
×
×
  • Create New...