Need a snowblower for C120

[loudtractor 46]

Looking for a snowblower to fit a c120, not sure exactly which part number I'm looking for. I'm in SW Michigan, South of Kalamazoo 35 miles. I could drive 100 or so miles for a decent one.

Thanks for looking,

Matt 

[Ed Kennell 38,227]

to the  This should be posted in our classified wanted section.     May be a Mod will move it for you.

[loudtractor 46]

OOPS! sorry, I thought that was where I had it! Still learning to navigate the site. Appreciate any help.

[gwest_ca-(File Mod) 11,047]

Single stage options

Front quick hitch introduced in 1973. Snowthrower rear frame has a 5/8" diameter round bar.

1973-74 model 6-6212 plus 6-9113

1974 model 6-6213 - (First model to include 8-0221 extensions without the front straight return - just a flat plate)

1975 model 6-6214 - (First model to include 8-0221 [103552 replaced by 93-1617 and 93-1617-01] side extensions with the front straight return. First model to have a cable spool on chute rotating crank) Chute crank support decal 104461.

1976 model 6-6215 ------ Chute crank support decal 104461. This one -

1976 model 66-42ST01 - Chute crank support decal 104461. and this one are likely identical. The model number format changed.

1977 model 76-42ST01 - Chute crank support decal 104461. This one

1978 model 86-42ST01 - Chute crank support decal 104461. and this one

1979 model 96-42ST01 - Chute crank support decal 104461. and this one may be all the same. They started using a different model number for each model year.

1980 model 06-42ST01 - (Last 42" model to use 4 grooved rollers for the chute)

1981-82 model 06-42ST02 - (First model to use plastic collar for the chute but was a retrofit for older models. Last model to use wheels)

1983 model 06-42ST03 - (First model to use skids)

1984-87 model 06-42ST04 - (Last model to use a 3/4" diameter driveshaft)

1987-89 model 06-42ST05 - (First model to use a 7/8" diameter driveshaft)

1990 model 06-42ST06 - (Last model to use a cable to turn the chute)

1991-93 model 06-42ST07 - (First model with tall chute retained by 3 individual grooved retainers)

1993-2001 model 79360 - (2001 and earlier will fit 2002-2007 with kit 105-1503) (1994 first year for replaceable blower housing scraper bar)

2002-2007 model 79362

[loudtractor 46]

Thanks! Exactly what I was looking for.

I have one here with no ID or stickers. It has , or is supposed to have, a control rod next to the chute control. Am I correct in thinking this is for an older short frame? It has wheels, and holes for side angle plates, 32" I think. I'll put a picture up later today

Thanks

Matt 

 

 

[loudtractor 46]

Here's a picture, any help with id or which tractor it fits would be awesome.

Thanks!

Matt 

[gwest_ca-(File Mod) 11,047]

Here is a list of the 32" models. The first 42" list is better suited to your tractor.

32" Snowthrower DNA - For tractors with horizontal shaft engines

 

1963 model ST-323 - Fits 701, 502, 552, 702, 603, 653, 753, 604

(Drive belt 1589 1/2" x 56.5") (Chute turned by belt 1590 3/8" x 43")

 

1964 model ST-324 - Fits 701, 502, 552, 702, 603, 633, 653, 753, 604, 654, 704, 854, 605, 655, 855

(Uses # 41 chain Pitch 1/2" and roller width 1/4") (Drive belt 1589 1/2" x 56.5") (First model to use cable on the chute)

 

1965 model ST-325 - Fits 701, 502, 552, 702, 603, 633, 653, 753, 604, 654, 704, 854, 605, 655, 855, 1045, 1055

(Uses # 41 chain Pitch 1/2" and roller width 1/4") (Drive belt 1589 1/2" x 56.5")

 

1966-1967 model ST-326 - Fits 701, 502, 552, 702, 603, 633, 653, 753, 604, 654, 704, 854, 605, 655, 855, 1045, 1055, 606, 656, 856, 876, 607, 657, 857, 867, 877

(Uses # 41 chain Pitch 1/2" and roller width 1/4") (Drive belt 1589 1/2" x 56.5")

 

1968-1969 model 6-2211 - Fits 500 Special, Commando 6, Commando 8, WorkHorse 700

(Formerly ST-326) (Uses # 41 chain Pitch 1/2" and roller width 1/4") (Drive belt 1589 1/2" x 56.5")

 

1971 model 6-0100 - Fits 800 Automatic, 800 Special, Bronco 14, Charger 12, Raider 10, Raider 12, WorkHorse 800

(No record of 6-0100 at Toro. Suspect it was same as 6-0200 plus 6-9112 in one package)

(Uses # 40 chain Pitch 1/2" and roller width 5/16") (Uses #101460 lift tube and #9750 5/8" x 69" belt)

 

1972 model 6-0200 plus 6-9112 - Fits Commando 800

(Uses # 40 chain Pitch 1/2" and roller width 5/16") (Uses #102729 lift tube and #102743 5/8" x 65.95" belt)

 

1972 model 6-0200 plus 6-9112 - Fits 800 Automatic, Bronco 14, Charger 10, Charger 12, Raider 8, Raider 10, Raider 12, Raider 14 

(Uses # 40 chain Pitch 1/2" and roller width 5/16") (Uses #101460 lift tube and #9750 5/8" x 69" belt)

 

1973 model 6-0200 plus  6-9131 - Fits 8hp 4-Speed

(Uses # 40 chain Pitch 1/2" and roller width 5/16") (Use #102729 lift tube and #102743 5/8" x 65.95" belt)

[loudtractor 46]

That's a great list! I do have a freshly restored 856. It looks like it might fit this one. I'm going to keep looking for one to fit the C120, now that I have a better idea what to look for..

Thanks!

Matt 

[Pullstart 62,913]

I see a beach ball @WHX??.  Is that a 6x6 in the background?

[loudtractor 46]

Yes sir. 1968 Amphicat. Restoration almost complete.

[WHX?? 48,828]

7 minutes ago, loudtractor said:

Yes sir. 1968 Amphicat. Restoration almost complete.

I was gonna say Argo but Ampicat works for me!  

 

I got two snowblowers here that you can have. Rather see them go to use rather than rusting away. One was on a 520 so thinking it would fit a C120. 

Enough parts to get one out of two for sure. 

Get some pics later. 

I'm sure between plow days and shows we could get them over. 

[loudtractor 46]

Sounds great! I'll look forward to it.

Spring is almost here!