Vinco 33 #1 Posted August 25, 2023 Is there a Wheel Horse that came from the factory with a Briggs 23D engine? I acquired one today that runs. 1 Share this post Link to post Share on other sites
ebinmaine 68,520 #2 Posted August 25, 2023 @AMC RULES @Lee1977 @kpinnc Share this post Link to post Share on other sites
ebinmaine 68,520 #3 Posted August 25, 2023 32 minutes ago, Vinco said: Is there a Wheel Horse that came from the factory with a Briggs 23D engine? I acquired one today that runs. The Briggs were a replacement engine. An excellent one. What's the model you have? Any pics ?? Share this post Link to post Share on other sites
AMC RULES 37,134 #4 Posted August 25, 2023 No, none to my knowledge. Share this post Link to post Share on other sites
Vinco 33 #5 Posted August 26, 2023 (edited) 3 hours ago, ebinmaine said: The Briggs were a replacement engine. An excellent one. What's the model you have? Any pics ?? It's 23D 0129. I'll get some pictures in a bit. Would it be too much for a 552 that has already been repowered with a Wisconsin? Edited August 26, 2023 by Vinco Share this post Link to post Share on other sites
kpinnc 12,620 #6 Posted August 26, 2023 44 minutes ago, Vinco said: It's 23D 0129. Best I can find online says a 23D is actually a 9hp engine. So if it fits on a 552, it should be ok. Share this post Link to post Share on other sites
Vinco 33 #7 Posted August 26, 2023 As huge as this engine is I was hoping it was more like 16 hp, but from what I read so far it should be a very torquey 9 hp! 1 Share this post Link to post Share on other sites
ebinmaine 68,520 #8 Posted August 26, 2023 5 hours ago, kpinnc said: fits on a 552 If it's the BIG single cylinder older Briggs it's a very tall engine for the HP. They're known as torque monsters. Share this post Link to post Share on other sites
Vinco 33 #9 Posted August 27, 2023 (edited) On 8/26/2023 at 2:48 AM, ebinmaine said: If it's the BIG single cylinder older Briggs... It is. It's 18" tall from the floor to the top of the shroud. The Wisconsin ACN that's on the tractor is 14". I don't have any Kohler singles so I don't have a practical concept of scale to compare those. It weighs a LOT! I can barely pick it up by myself, though that's not saying all that much, as I have lost a huge amount of strength over the last 2 years because of medical stuff. Edited August 28, 2023 by Vinco 1 Share this post Link to post Share on other sites
ebinmaine 68,520 #10 Posted August 27, 2023 On 8/25/2023 at 5:22 PM, Vinco said: Is there a Wheel Horse that came from the factory with a Briggs 23D engine? I acquired one today that runs. Got any pics of this? Share this post Link to post Share on other sites
Vinco 33 #11 Posted August 28, 2023 I measured again. The Briggs is 18" tall, but the Wisconsin ACN is actually just 14" tall. It sits on a 1" spacer on the 552 frame, and with that the crankshaft centerline is about 4.25" up from the frame. The Briggs crankshaft centerline is about 6.25" off the floor. So it will likely not be a good fit on the 552 because of the belt drive. Peek at the 552 in the last picture. 1 Share this post Link to post Share on other sites
