throttle shaft bushing

[Wheelhorse#1 1,666]

Anyone know of a good source for throttle shaft bushing for a Carter carb.The folks on flea bay want a arm and leg.  

Edited November 6, 2022 by Wheelhorse#1

[WHX?? 48,828]

@ebinmaine does carbs maybe he knows? 

[squonk 41,141]

Hillman drawer at Ace Hardware.

[Achto 27,597]

1 minute ago, squonk said:

Hillman drawer at Ace Hardware

 

 

They do not have 7/16" od x 1/4" id x 1/8" thick. They do have 7/16 x 1/4 x 1/16. Buy two & double them up. Works fine, last long time.

[oliver2-44 9,758]

3 minutes ago, Achto said:

 

 

They do not have 7/16" od x 1/4" id x 1/8" thick. They do have 7/16 x 1/4 x 1/16. Buy two & double them up. Works fine, last long time.

Exactly what I use. 

[Wheelhorse#1 1,666]

12 minutes ago, Achto said:

 

 

They do not have 7/16" od x 1/4" id x 1/8" thick. They do have 7/16 x 1/4 x 1/16. Buy two & double them up. Works fine, last long time.

Thanks Guys ,y’all never fail to help a fellow out !

Much appreciated ! 

[ebinmaine 67,567]

18 minutes ago, Wheelhorse#1 said:

Thanks Guys ,y’all never fail to help a fellow out !

Much appreciated ! 

How many ya need?

I can mail em out if'n you don't have a good local source.   

[Wheelhorse#1 1,666]

9 minutes ago, ebinmaine said:

How many ya need?

I can mail em out if'n you don't have a good local source.   

Thank you! I just need a couple.We have a Ace here,I’ll go and check to see tomorrow if they have it.

If not I’ll get back to you.Thanks for the offer .

[8ntruck 7,015]

3 hours ago, Achto said:

 

 

They do not have 7/16" od x 1/4" id x 1/8" thick. They do have 7/16 x 1/4 x 1/16. Buy two & double them up. Works fine, last long time.

Might put a small dab of grease between the two bushings before putting them into the carb.  The grease will act as a seal to help prevent a possible air leak that could drive you nuts trying to find.

[WHX?? 48,828]

Someday I'm gonna mail you a bushel of carbs that need it EB @ebinmaine 

I have just had so much good luck with the knock offs I see no need unless I really really have to stay orginal on a resto. 

 Yes sometimes the case but still to just get one moving. 

I know I know we have had this discussion before. The choke backwards on the knock offs for the big blocks can be an issue but for how cheap they are?? 

Last post here. 

 

Edited November 6, 2022 by WHX??

[ebinmaine 67,567]

8 hours ago, WHX?? said:

choke backwards on the knock offs for the big blocks can be an issue but for how cheap they are?

 

It's great that you're having good luck on the cheapos. 

Just wasn't my experience. 

 

FYI. Isavetractors does sell an import replacement carb with the choke cable the right way. 

I've seen 2 so far. They seem to work well.  For the price of them I'd still rebuild an original one but the option is there.  

[Achto 27,597]

I've always had good luck rebuilding the Carter carbs, even keep kits in stock. Have not tried the China carbs.

[squonk 41,141]

I have a Walbro on a K341 that I can't seem to find a kit # . Edit I think its 25 041 06S? 

Edited November 6, 2022 by squonk

[pfrederi 17,741]

8 minutes ago, squonk said:

I have a Walboro on a K341 that I can't seem to find a kit

  Do you need Walbro K1-WHG  ??  Fixed jet??

Edited November 6, 2022 by pfrederi

[squonk 41,141]

14 minutes ago, pfrederi said:

  Do you need Walbro K1-WHG  ??  Fixed jet??

Not sure yet. This is on my neighbor's tractor. Kohler engine.  Started running like crap. There is what looks like a mixture screw and an idle mix screw. If I take what looks like the mixture screw out gas comes out. I'm wondering if the float is shot

Edited November 6, 2022 by squonk

[pfrederi 17,741]

Looks like this

 

 

[squonk 41,141]

This is the carb 

 

[pfrederi 17,741]

It is adkustabke  but I wonder if the float valve and little spring are the same...